Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 47+: 60 results shown for Piston.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Rocker Bolts
    Historical mailing list - jeremyp
    Sat, 15 Nov 2003 22:34:55 -0500
    ...I have successfully replaced my dead piston and two jugs - without removing the engine and it was a pain. (don't ask.) I have...
  • Re: Inline 4 Recommendation
    Historical mailing list - Mark Cumnock
    Mon, 1 Mar 2004 22:41:15 -0500
    I have a 2.0 (with piston oilers) ,with a 1.8 head, digifant II fuel injection . I am using Darrell Boehler's Digitool...
  • Re: Nitrous on diesel?
    Historical mailing list - Andrew Grebneff
    Wed, 1 Sep 2004 22:14:28 +1200
    >Yes, with propane injection, and very careful mixture tuning. >Otherwise, NASA will be calling you to stop launching diesel pistons >into orbit! >TEMiller > >Andrew...
  • Re: can you put 17 inch wheels on a 84 vanagon?
    Historical mailing list - BenT Syncro
    Tue, 30 Sep 2008 00:21:45 -0700
    ...Audi dual-piston calipers w/ 303mm rotors. 50 series tires. In each application, the wheel and tire assembly weighs less than the stock bare...
  • Re: Whistle-like sound from front brake (searched)
    Historical mailing list - neil N
    Wed, 4 Feb 2009 14:59:28 -0800
    ...aside from what *looks* like a fubar'd dust seal, the piston itself may not be fully returning or possibly seized. These may have...
  • Re: '82-2.0 teardown. help me find the knocking please
    Historical mailing list - B.J.R.
    Tue, 2 Jun 2009 00:47:23 -0700
    ...help me find the knocking please well, you can remove the rod nuts, bolts , and caps once you remove pistons. That'll get you...
  • Re: Roadhaus - Need an Engine
    Historical mailing list - ROBERT DONALDS
    Wed, 5 May 2004 11:27:27 -0400
    ...failure of the third set of 2.2L pistons I reverted > to stock 2.1L pistons. > > Unfortunately, because of a questionable head, the result...
  • Re: brakes
    Historical mailing list - Dennis Haynes
    Wed, 20 Oct 2004 19:08:52 -0400
    ...Front pads are same surface area and caliper pistons also. The main problem is that the Vanagon is heavier. For the rear brakes, get...
  • Re: shifter linkage solved and the real problem persists...groan!
    Historical mailing list - Dennis Haynes
    Sat, 18 Mar 2006 07:33:59 -0500
    ...ATE is the only cylinder I know with the correct details including the spring to preload the pistons to push tem out against the...
  • Re: Clutch Play
    Historical mailing list - Jim & Melody
    Tue, 25 May 1999 12:44:53 -0600
    ...My guess is that the holes in the master cylinder > > piston yoke is well worn as is the pin that goes through it. It...
  • Gasoline Octane rating explained
    Historical mailing list - Stuart MacMillan
    Fri, 25 Feb 2000 09:33:26 -0800
    ...The flame continues to burn through the fuel/air mixture as the piston moves down, creating an even expansion of gasses to produce the...
  • FIX]auto tranny experts HELP! UPdate
    Historical mailing list - Dan Noll
    Tue, 11 Jun 2002 21:22:58 EDT
    ...This all started when I tried to fix my 2nd gear brake leak. (I posted before and got no response)I destroyed the piston...
  • Re: A new project..inline 4 VW van
    Historical mailing list - pdooley
    Sun, 6 Jun 2010 16:12:16 -0400
    ...ponies and I am told they are better designed for lower RPM running with a > forged crank and some under the piston oil squirters.
  • Re: More horse power from the 2.1??
    Historical mailing list
    Fri, 26 Jul 1996 11:12:19 -0400
    ...Also, the pressures created by the piston compression are far higher than any turbo can create during the intake stroke. Jim Davis 87 GL...
  • Re: motor swapping
    Historical mailing list
    Tue, 3 Jan 95 12:17:42 EST
    a la David Schwarze: >The "1835" engine has the same case as a 1600, just with bigger pistons and >cylinders (and a stroker crankshaft...
  • Re: 2.1L Cylinder barrel rebore (Wow!)
    Historical mailing list - Robert Lilley
    Wed, 22 Dec 1999 06:29:52 EST
    ...He did not have any sources for pistons except one, when I called they said that they have not done any. The engine I...
  • Re: spark plugs: 8 plugs in a 4-banger!
    Historical mailing list - Robert Lilley
    Thu, 7 Sep 2000 23:04:56 EDT
    ...plug, having two plugs in the T4 engines significantly reduce the piston wear. The plug is at the top of the cylinder. I was...
  • Machine shop recommendation...
    Historical mailing list - Daniel Schmitz
    Sun, 26 Nov 2000 11:33:10 -0800
    ...Grind crankshaft (if necessary) balance a new set of pistons, my connecting rods & crank Do a good 3-angle valve job on two VW...
  • Re: bilstiens.. are they worth it
    Historical mailing list - DaveC
    Sun, 12 Aug 2001 00:20:59 -0700
    ...anywa, who has >them, and how ya like them My experience (not with a Vanagon/Westy) is that Bilsteins are built better (larger piston...
  • Re: Is it Wasserboxer or waterboxer?
    Historical mailing list - Dave Baker
    Sun, 30 Dec 2001 12:00:30 -0600
    ...the name of the person who engineered the > VW engine with pistons that "box" each other, or was that a joke or a myth...
  • Re: Caliper resetting pliers
    Historical mailing list - Hector Zapata
    Sun, 24 Mar 2002 19:31:55 -0800
    ...cheap) says that there are resetting pliars made for pushing the > pistons back into the brake calipers (while the calipers are still on the...
  • Valve guide removal / replacement
    Historical mailing list - Herr Wibo Fichten
    Tue, 30 Mar 2004 00:02:35 -0400
    ...In fact except for a single picture in Bentley, that suggests it, I don't even know if they come out from the piston...
  • Re: Strange braking problem!!!! (this week challenge)
    Historical mailing list - jbange
    Sun, 31 Oct 2004 08:25:30 -0800
    ...I had a '67 Dodge Dart with a bad master cylinder piston seal which, if you pressed the pedal down slowly, would allow the...
  • Re: Valve confusion
    Historical mailing list - Dennis Haynes
    Wed, 15 Nov 2006 06:05:25 -0500
    ...From what I understand, it says to adjust the screw against the valve stem with piston at TDC, and them screw it in 2...
  • Re: vanagon Digest - 31 Aug 2002 - Special issue (#2002-1058)
    Historical mailing list - Chuck Mathis
    Sat, 31 Aug 2002 22:21:05 EDT
    ...You have pulses being caused by the pistons. These occur >rhythmicly and as with any other rhytmic system, you can get reinforcement >of >the...
  • Off with its head! (Further adventures with right head on an '87 2.1 l)
    Historical mailing list - Matt Roberds
    Sun, 1 Jul 2007 04:18:01 -0500
    ...Or is this a recipe for problems later? We are trying to avoid having to pull the piston pins and pistons; the engine is...
  • Re: Redline (the speed,not the oil) (was: with all this talk about prices...)
    Historical mailing list - Mark Vermillion
    Sun, 12 Jan 2003 01:47:50 -0500
    ...have a 3 brand new pistons & sleeves that were given to me after the PO > > >>>threw a piston when driving down the Alcan (he...
  • thanks : oil pump change in the van??
    Historical mailing list - Jonce Fancher
    Wed, 2 Nov 2005 22:35:09 -0500
    ...one is on the engine stand with 1 head off and i have 2 sets of new pistons and cylinders the lower end is...
  • RE: Upgraded Brakes Bus/Vanagon?
    Historical mailing list - Dennis Haynes
    Mon, 31 Mar 97 05:09:46 UT
    ...The pads are much larger and the caliper is now a single piston. The rotors are increased in thickness from 13 to 15 mm...
  • Re: AT problems again - Dennis H.?
    Historical mailing list - Dennis Haynes
    Tue, 23 Sep 2003 18:16:40 -0400
    ...The direct drive drum assembly relies on piston style ring for sealing while it spins on the pump hub. These rings can break due...
  • Re: 71 no start
    Historical mailing list
    Thu, 29 Jun 1995 23:33:25 -0400
    ...in checking when the rotor is at the #1 position the plug for #1 sparks, the piston is at TDC and the valve clearance...
  • Re: Question #2 - clutch bleeding
    Historical mailing list - Sean Bartnik
    Thu, 9 Apr 1998 16:59:20 EDT
    ...Or could too > much air in the system be locking up the piston in the slave cylinder? I wouldn't think so, but I...
  • Re: Ring job?
    Historical mailing list - Vince Jahn
    Wed, 13 Oct 2004 21:20:46 -0700
    I'm ok on replacing the Cyl and Piston set if needed, but can it be done while the engine is still mounted?. Is...
  • Re: Positive Crankcase Ventilation
    Historical mailing list - Alistair Bell
    Sun, 13 Aug 2023 16:47:17 -0700
    ...So here goes cut and paste. > > > PCV=Positive Crankcase Ventilation. > > This is the method of extracting piston blowby and other fumes from the crankcase...
  • Re: I-4 owner experrience
    Historical mailing list - Ed McLean
    Wed, 15 May 2013 15:31:23 -0400
    ...o2 sensor suddenly overheated in Kayenta, AZ and then cracked a piston in Orderville, UT with 5000 miles on the conversion. That was a...
  • Re: 2.0L I4 Opportunities
    Historical mailing list - mark drillock
    Tue, 14 May 2013 07:53:36 -0700
    ...The early ones have unique pistons and rings that are costly. Later ones share ABA parts AFAIK. Used in the small Audi car for...
  • Re: source for rebuilt ATE calipers?
    Historical mailing list - Jason
    Tue, 19 Jun 2012 19:45:37 -0400
    ...I was able to polish the pistons and reassemble them. Flush your brake fluid guys! Jason On Mon, Jun 18, 2012 at 1:11...
  • Re: Coasties with Vanagons? was- LVC: OPOC engine
    Historical mailing list - Boucheron
    Fri, 4 Dec 2009 16:19:20 -0500
    ...engines running JP5 fuel thru Fairbanks Morse 12 cyl with 2 >> pistons/cyl vertically opposed. Similar setup..2 injectors per cyl >> at about 3000HP...
  • Re: newly installed engine won't turn
    Historical mailing list
    Thu, 18 Jul 1996 16:46:38 -0700 (PDT)
    ...I managed to put a valve through my piston so I was > afforded the oppportunity to put a new engine in. I got a...
  • Changing Rods
    Historical mailing list - David Bayer
    Tue, 7 Apr 1998 13:34:29 -0700
    ...one of the rods to have it checked, since the connected piston was chipped after slamming into an intake valve which had seized on...
  • Re: Scoop for breather?
    Historical mailing list - CHRIS STANN
    Tue, 8 Aug 2000 07:24:44 -0500
    ...it comes out the tailpipe, or as fast as your moving pistons and valves will allow it to. What are you running in your...
  • Re: Blue smoke at start-up
    Historical mailing list - John Rodgers
    Mon, 14 Jan 2002 22:09:26 -0600
    ...My van did this moke routine and not long after I had a piston fail. A compression test will tell you a lot about...
  • Re: AT Brake Band Adjustment
    Historical mailing list - jbange
    Thu, 23 Sep 2004 19:43:36 -0700
    ...The other side is >connected to a hydraulic piston. > >The whole complicated tighten/loosen/tighten routine... I guess it is >supposed to get the...
  • Re: cylinder hone question
    Historical mailing list - John Rodgers
    Thu, 22 Jan 2004 07:01:31 -0600
    ...wrote: > I am in the process of rebuilding a 1.9L, and am just >about ready to clean up the pistons and hone the...
  • Re: has anyone seen July 2003 VWT?
    Historical mailing list - Stan Wilder
    Sun, 18 May 2003 12:00:55 -0700
    ...The Mystery oil will clean your oil passages, crankcase internally, lifters, pistons, piston tops and groves and just in general remove all of the...
  • Re: Carat new engine locked up
    Historical mailing list - Dennis Haynes
    Fri, 18 Mar 2016 19:34:07 -0400
    ...I have seen those multi piece oil rings get messed up during install and then getting jammed between the piston and cylinder jamming up...
  • Fwd: how much interest IS there in the 5cyl conversion???
    Historical mailing list - Helmut Zeidler
    Thu, 14 Jan 1999 09:25:21 +0100
    ...2) Blue smoke while slowing down on the engine, turns out, weared piston rings, 300 USD parts replacement. I changed connection rod bearings at...
  • Re: Boston Bob Engine - Follow Up
    Historical mailing list - Frank Grunthaner
    Sun, 12 Aug 2001 00:59:06 EDT
    ...piston as the slipper) because of too tight a tolerance at the base of the cylinder bore, or too large of a piston) Taper...
  • Re: GoWesty Auto Parts QSC piston kits
    Historical mailing list - Ken Wilford
    Thu, 31 Mar 2011 17:54:47 -0400
    ...The 96mm piston set I can do for >>>> $299 for Vanagon list members. Just let me know. >>>> >>>> PS, I will gladly give anyone who...
  • Re: Cross-country trip report
    Historical mailing list - Scott Daniel - Turbovans
    Thu, 21 Jul 2011 16:25:17 -0700
    ...that I had those piston rings in my hands only about two months ago .. and that engine is not fully, fully rebuilt bored out...
  • Re: Stalling at stop lights
    Historical mailing list - Dennis Haynes
    Mon, 25 Apr 2005 23:52:53 -0400
    ...Maybe you had an 86? Which calipers did you have for the front brakes? Single or dual piston. 86 got the later single piston...
  • Re: Master Cylinder
    Historical mailing list - Jeffrey Schwaia
    Wed, 1 Mar 2006 10:43:26 -0800
    ...he is saying is that the fluid is leaking past the piston internally hence the the pedal is soft and goes to the floor...
  • Re: stainless steel coolant pipes
    Historical mailing list - Andrew Grebneff
    Thu, 6 May 2010 23:35:40 +1200
    ...The piston liners inside the engine are cast iron > with steel studs holding the heads on. Any way you look at it the van...
  • Re: FYI, Syncro FS in Northern Ohio
    Historical mailing list - Mark A Kippert
    Wed, 9 Dec 2009 22:19:47 -0500
    ...Synchro 4wd van with solid body, rebuilt engine >> with >> new heads, pistons, etc ($5000plus) with NO miles on it. New tires, >> brakes. Interior very...
  • Re: 2200cc liners
    Historical mailing list - David Kao
    Wed, 12 Sep 2007 18:52:53 -0700
    ...Most retailers can get you > the pistons and cylinders. > > BenT > ____________________________________________________________________________________ Check out the hottest 2008 models today at Yahoo! Autos. http://autos.yahoo.com...
  • what motor parts interchange???
    Historical mailing list - Street Bugs
    Sun, 15 Dec 1996 21:51:12 GMT
    ...my questions are what is interchangable between the two motor? as far as heads,pistons,altenator,water pump,flywheel,rocker arms,valves,oil pump...
  • Re: 1.6NA Diesel Rebuild Options ???
    Historical mailing list - Michael Snow
    Fri, 20 Aug 1999 06:00:11 -0700
    ...all reciprocating > parts .Flywheel,pressure plate,front pulley and rods > and pistons and them do > a full engine balance .I did this to my...
  • Re: Euro Vanagons 2.1L have 112 horsies......how do they accomplish t his?.....compression @ 10:1?.....G-cam?
    Historical mailing list - MDC Vanagon
    Thu, 14 Mar 2002 15:43:06 -0800
    ...and you will get a cookie Malibu Tony 1.9L.......eventually a 2.2L or 2.4L if I can find the pistons cheaply
  • Re: Fw: 86 syncro I-4 swap
    Historical mailing list - John Rodgers
    Wed, 4 Jun 2003 12:18:18 -0500
    ...machined connecting rods for 80mm stroke. > Go Westy exclusive modified 95mm pistons. > A different, exclusive GoWesty proprietary camshaft grind specifically > for this engine. > This...
  • Re: vanagon top speed, extrapolation
    Historical mailing list - Andrew Grebneff
    Tue, 7 Sep 2004 20:14:17 +1200
    >I had my 83 Westy Air Cooled up to 85 mph once. >That's when I blew #3 piston and showered the big Dodge...