Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 40+: 60 results shown for Piston.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Replacing the master cylinder
    Historical mailing list - David Clarkson
    Tue, 13 May 2008 20:05:06 EDT
    ...If you go too far then you may press the piston into a rusted area of the cylinder and score the seals (rebuild or...
  • Re: Best source of parts for a rebuild
    Historical mailing list - Mike Collum
    Mon, 13 Oct 2008 19:55:15 -0400
    ...According to the Pro Training Manual, the 2.1 simply has a > 7mm longer stroke (94mm piston, so 4.7 * 4.7 * pi * .7cm...
  • Re: Dreaded water jacket head gasket leak strikes
    Historical mailing list - Stuart MacMillan
    Sun, 20 Dec 2015 12:21:34 -0800
    Yeah, how did you do that? The Bentley shows sleeve is installed over the piston, then the assembly is inserted over the rod and...
  • Factory New VW Diesel Motors
    Historical mailing list
    Tue, 20 Oct 1998 20:21:38 EDT
    ...These motors are true TD motors and have the oil squirters under the pistons so that the pistons get the extra cooling they need...
  • Re: HELP ME!!! I pulled my pistons but forgot to mark my sleeves!!!!!!!!!!! Does it matter which way the cylinder sleeves go back in?? What if I interchanged them. I noticed that they are stamped on the sided in increments. Some kind of ID on each on But then there are then there is one digit that goes in increments (22..24..26..28 ) for each cylinder. I did honed the glazed out of the cylinders because I'm re-ringing them...So What should I do.???? GOD help ME PLEASE!!!!
    Historical mailing list - Stan Wilder
    Tue, 14 Aug 2001 21:16:28 -0500
    Don't forget that all the little arrows on the pistons points towards the flywheel. If you have hydraulic lifters set them to one...
  • Re: Wasserboxer Reputation . long
    Historical mailing list - Stan Wilder
    Tue, 10 Dec 2002 00:17:54 -0600
    ...techbull.html that the pistons should be fitted looser and the rods notched to spray oil at the piston undersides. Those things in addition...
  • Re: yet another engine choice - VW "twincharger"
    Historical mailing list - Jim Felder
    Wed, 28 Sep 2005 09:52:14 -0500
    ...crank out the > bottom of the pan in no time. > Melted piston's are a big bonus with a big push of intake . This...
  • Re: 2.1 ring recommendations
    Historical mailing list - Ken Wilford
    Wed, 27 May 2009 10:48:33 -0400
    ...Clean the pistons and ring grooves with a broken piece of old ring. When you put the new rings on bathe the pistons and...
  • Re: 87 Vanagon Crisis [long]
    Historical mailing list - Brent Christensen
    Thu, 15 Apr 1999 09:28:17 -0700
    ...The noise you mention is probably due to "piston slap" or "rod noise" which is essentially also cause by excessive clearance between the piston...
  • Re: Has anyone "stroked" a 2.1L motor
    Historical mailing list - Robert Donalds
    Tue, 12 Mar 2002 11:43:15 -0500
    ...Bigger pistons would provide more low end torque but this engine does not easily take larger pistons without allot of money and labor. one...
  • Re: Clutch Slave Cylinder Bleed problem (How to replace your slave cylinder)
    Historical mailing list - Brent Christensen
    Fri, 23 Nov 2001 15:54:54 -0800
    ...The greater outer diameter points to the rear end of the piston, where the spring is attached. Put spring and piston back into the...
  • Re: engine swap (ignorant questions) -> EV piston slap
    Historical mailing list - "L-Soft list server at Vanagon List (1.8c)"
    Thu, 11 Dec 1997 15:52:47 -0800
    ...Try HELP. >>>>> >>>>> >> I don't believe "Piston Slap" is HYPE, as it was claimed. I have a >>>>> >>>>> > Unknown command - "I". Try HELP. >>>>> Unknown command...
  • Re: BMEP question
    Historical mailing list - Clive Smith
    Fri, 8 Nov 2002 00:16:43 -0000
    ...What does this mean (sic)? It is a measure of the TORQUE, as pressure on the piston acting against the leverage of the crank...
  • Re: Clutch Slave Cylinder
    Historical mailing list - Tom Forhan
    Sun, 30 Sep 2007 14:54:43 -0700
    ...Somehow, while detached from the clutch arm, the piston had slid past its normal travel point. It could be that someone stepped on the...
  • Re: Air cooled camshaft
    Historical mailing list - Dennis Haynes
    Mon, 24 Mar 2008 19:13:10 -0400
    ...The Brazilian piston sets have a lousy finish but they will usually work just fine if the case and heads are good. I gave...
  • Re: Model info on a SD709 compressor needed
    Historical mailing list - Stan Wilder
    Wed, 18 Aug 2004 15:35:12 -0500
    ...Seven piston and nine Cubic Inches. Stan Wilder www.engineceramics.com ----- Original Message ----- From: "Robert Lilley" <RClilleyjr@COX.NET> To: <vanagon@GERRY.VANAGON.COM...
  • Re: How does a leak down tester work???
    Historical mailing list - George Goff
    Wed, 26 Jan 2005 08:13:59 EST
    ...As matter of safety, the piston in the subject cylinder must be at bottom dead center so that the application of the air does...
  • leak down verdict
    Historical mailing list - Jamie Foust
    Thu, 24 Aug 2006 09:54:52 -0500
    ...I'll inspect the pistons, heads, and cylinders, maybe do a re-ring and hone, but I'm happy with the compression results, maybe...
  • Hydraulic Lifter Adjustments
    Historical mailing list - vanagonvw
    Wed, 27 Jun 2007 21:49:34 -0600
    ...Off by a few degrees, and the air pressure just pushes the piston down, and the motor around, in whichever direction. :-) To get started...
  • Re: Oldest
    Historical mailing list - Scott Daniel - Turbovans
    Fri, 7 Oct 2011 22:39:24 -0700
    ...A bunch of hippies had a load of > tapestries etc(drugs???....ya think??) blew a hole in a piston on > their way to a...
  • 1.9L case half ?? loctite 515 sealant
    Historical mailing list - Jonce Fancher
    Wed, 15 Mar 2006 23:08:20 -0500
    ...As for the pistons and cylinders is the Kit of goo used for between the case and cylinders or just use the green O...
  • Re: Dreaded water jacket head gasket leak strikes
    Historical mailing list - Stuart MacMillan
    Sun, 20 Dec 2015 17:25:31 -0800
    ...I also used a cut down ring compressor to get the Pistons in. I know folk do I the heads with engine installed, but...
  • Re: Middle of BC trip report, roadside repair update and brake question
    Historical mailing list - Dave Mcneely
    Mon, 9 Jul 2012 17:19:10 -0500
    ...Any ideas? When the piston in the master cylinder is worn, brake fluid can bypass. "pumping" can sometimes catch more fluid and give the...
  • Re: Rear Drum-to-Disc Swap?
    Historical mailing list - Bob Stevens
    Mon, 22 Mar 2010 20:47:27 -0600
    I installed the Overland single piston BB kit up front with 288mm vented rotors a few years ago. That improved my braking performance and...
  • Re: MYT (Massive Yet Tiny) Engine
    Historical mailing list - Allan Streib
    Sat, 6 Feb 2010 09:44:40 -0500
    ...It's an > interesting concept, but just offhand I can tell you that sealing > those piston chambers is likely a major long term reliability...
  • Re: best place to buy "overhaul kit/parts" for my 85 Vanagon (water) 1.9l engine
    Historical mailing list - Ken Wilford
    Sat, 31 Oct 2009 15:57:18 -0400
    ...Do you want just rings or new pistons and cylinders? What about heads? Let me know and I'll get everything together for you...
  • Re: motor swapping
    Historical mailing list
    Tue, 03 Jan 1995 12:41:34 +0500
    Chris Schalick writes: >The "1835" engine has the same case as a 1600, just with bigger pistons and >cylinders (and a stroker crankshaft? Damn...
  • Re: compression
    Historical mailing list - GMBulley
    Mon, 23 Mar 1998 09:09:24 EST
    ...suggestions. >> Bad news, whatever the cause. My guesses, somewhat in order: Pistons in #1 & #2 installed upside-down, and have worn out the cylinder...
  • Re: 1.9L Engin Question
    Historical mailing list - Dave C.
    Sat, 16 Dec 2000 12:12:42 +0000
    ...soon and thus the explosion pushes downward on an upward moving piston) not lifter knocks. Detonation is very bad for engine life. And no...
  • Blown engine: Lists opinions on prognosis, possible rebuild, please!
    Historical mailing list - George Lehman
    Tue, 17 Jul 2001 11:20:05 +0800
    ...What is probable cause? Valves? Hole in piston? or what? Am heading back to the Twin Cities with a dolly on tuesday to tow...
  • Re: VW Canada motors
    Historical mailing list - Matthew Pollard
    Fri, 14 Jun 2002 10:00:59 -0700
    ...wrote: > > > Isn't the case a sand-casting? Same with the heads? Cylinder linings? > > Rods? > > > Pistons? Milled or turned to tolerances after? > > > > > > According to...
  • Re: Brakes
    Historical mailing list - Dan Brideau
    Tue, 7 Oct 2003 15:26:05 -0400
    ...I suspect the seal around the piston would "parachute" out a little with a faster pedal application. Just a guess, but the new master...
  • Re: Dragging front brakes...why? how?
    Historical mailing list - David Brodbeck
    Wed, 31 Mar 2004 21:13:24 -0500
    ...worrisome. > > <snip> > > The two things that come to mind are, 1. pistons in the calipers are > sticking, and 2. the fluid return hole in...
  • Re: Sudden loss of power, running rough and burning oil
    Historical mailing list - phil cain
    Wed, 28 Jul 2004 19:44:07 -0700
    ...this means that you have a problem with the rings or piston, had it stayed at 80PSI this would have meant that the valves...
  • Re: Success! (Cylinder install after removal stuck to head)
    Historical mailing list - zolo
    Sat, 7 Dec 2002 23:27:15 -0800
    ...Clean the piston and rings. Offset the rings 90 >degrees. Position the band so that its ears are between the top and >bottom >head...
  • Looking for a rebuildable 2.1 Engine
    Historical mailing list - Clifford P Gottschalk
    Tue, 1 Jun 1999 07:50:47 -0600
    ...The case is shot, one rod and possibly one piston, everything else looks good to this point. What I am looking for is a...
  • Re: Manual trans replacement
    Historical mailing list - mark drillock
    Tue, 10 Mar 2009 07:49:42 -0700
    ...Put spring and piston back into the >> > slave cylinder, push the piston down a little, and insert the >> > circlip. >> > >> >5. Now turn the slave...
  • Re: 2.1 Wasserboxer
    Historical mailing list - Jerry
    Fri, 12 Jan 2007 10:54:54 -0600
    ...As far as the pistons I can offer you german piston or Cofap nobody has ever told me they felt any differance in performance...
  • Re: *Sigh* Leaky Wheel Cylinder (PICS)
    Historical mailing list - Dennis Haynes
    Sat, 5 Sep 2009 16:58:36 -0400
    ...Then > when the piston does move the leaks begin. > > Also depending on brake shoe material you may be ready for brakes anyway. > > Dennis I...
  • Re: oil pressure
    Historical mailing list - John Scheckel
    Tue, 6 Jul 1999 01:50:50 -0700
    ...Could you have put the rings in wrong? If the only thing you did was > replace the pistons, I would start trouble shooting there...
  • Re: 2.2L EuroCars Engine vs 2.1l Boston Engine
    Historical mailing list - Bill N
    Fri, 23 Aug 2002 09:44:34 -0700
    ...and increased piston skirt clearance > > 2.1 "Big Valve" Upgrade > Upgrade: $3050 + core > This package offers the same upgrades as above with the addition...
  • Re: Spark plugs - 2.l L
    Historical mailing list - Chris S.
    Sun, 28 Sep 2014 12:51:28 -0400
    ...They are too long bringing the flame front close to the piston. If you want the multi tips get the 4477 Quads or the...
  • Re: Brake Caliper Done?
    Historical mailing list - Chris S.
    Sat, 17 Mar 2012 13:49:18 -0400
    ...of the driver side was lowest and I cannot squeeze that piston back in no matter what I do. It this thing toast? I...
  • Friday - yet more aircraft pictures
    Historical mailing list - Alistair Bell
    Fri, 21 Jan 2011 07:57:35 -0800
    ...That's a quarter on the prop shaft and the piston, to give you an idea of the size. And as a bonus, a...
  • Re: Piston pins
    Historical mailing list
    Tue, 5 Mar 96 22:24 CST
    Bob Hoover wrote an excellent sermon on persuading gudgeon pins in and out: >Any fool can pound on things and most of us do...
  • Re: 87' Vanagon
    Historical mailing list - TBill
    Tue, 7 Oct 1997 02:58:51 -0700
    ...When I rev it a little, it's even more obvious not all 4 > pistons are firing. > > After a while everything seems ok and...
  • Re: Mushy Brakes update
    Historical mailing list - Jeffrey R
    Sun, 19 Mar 2000 03:27:04 EST
    ...Is it possible the extra travel of the wheel cylinder pistons as a result of the excessive wear to the drums caused the wheel...
  • Re: I am almost ready to shoot my vaagon!
    Historical mailing list - Andrew Grebneff
    Mon, 11 Dec 2000 22:05:13 +1200
    ...Too little air and too much fuel and you get incomplete burning, fouled plugs/pistons/rings etc, smoke, excessive consumption...and that hidden danger...
  • This is scary - delivery of the oversize set
    Historical mailing list - Zoltan
    Tue, 17 Apr 2001 10:20:38 -0700
    I have ordered a set of oversize piston and liner yesterday afternoon and this morning at ten it was delivered to my door by...
  • Diesel coolant circulation
    Historical mailing list - Mary Beth and Chris Geiser
    Sun, 13 May 2001 08:30:37 -0500
    ...When I look at the block (still in the van), there are two coolant circulation holes around the bottom of the piston closest to...
  • Re: full throttle switch boost?
    Historical mailing list - Dennis Haynes
    Thu, 30 Aug 2001 21:18:47 -0400
    ...The ultimate goal is to richen the mixture slightly to avoid detonation, burned valves and melted pistons. Dennis -----Original Message----- From: Vanagon Mailing List...
  • Re: Weird Hatch Struts?
    Historical mailing list - Loren Busch
    Wed, 18 Apr 2012 08:53:46 -0700
    ...the split opening was just wide enough to slip over the piston (small) end of the hatch strut. And when he opened the rear...
  • Re: Vanagon Down in Clinton,Oklahoma
    Historical mailing list - EMZ
    Tue, 19 Oct 1999 12:07:27 -0400
    ...vehicle, forward toward the driver, > > is the one that blew the piston. Symptoms were massive white smoke out > the tail pipe, aluminum particles welded...
  • Re: Separating heads from cylinders
    Historical mailing list - Coby Smolens
    Tue, 28 Aug 2001 16:21:38 -0700
    Right - the problem is that the heads will move away from the block with the cylinders as the crank pushes the pistons outward. Compressed...
  • Re: Warren Chapman drives his Syncro into the sunset...
    Historical mailing list - Benny boy
    Wed, 16 Sep 2009 23:22:33 -0400
    ...Sir, rest in peace, please! A very sad day this is. "Ben, i hate that piston slap noise!!! Got to fix that, i'm...
  • I need cylinders only.
    Historical mailing list - Gerald Skerbitz
    Mon, 9 Oct 1995 13:20:42 -0500 (CDT)
    ...The pistons are in good shape so I am looking for sombody that sells cylinders only, not in an assembly package. Does anybody know...
  • 1.9L & 2.1L Water pump interchange
    Historical mailing list
    Wed, 25 Dec 1996 21:17:00 -0500
    I am rebuilding a 1984 1.9L Vanagon engine to 2.1L specs (2,1L cyls, pistons, etc.). When finished, I plan to put...
  • Re: Bad heads and a noise
    Historical mailing list - TBill
    Sat, 6 Dec 1997 16:49:30 -0800
    ...Speculation has been that the valves are getting hit by the piston, and it > does kinda have that metal-hitting-metal sound. What's...
  • Re: 81
    Historical mailing list - Daniel Schmitz
    Thu, 31 Aug 2000 10:30:32 -0700
    ...When your engine's #1 piston is at Top Dead Center on the Compression stroke, your ignition rotor needs to be pointing to cyl...
  • Diesel Performance
    Historical mailing list - Jeffrey Earl
    Tue, 30 Sep 2003 12:23:45 -0700
    ...Wonder if those tiny Japanese guys could be hired to slip in thru my intake manifold and look for piston wear, carbon buildup, and...