Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 39+: 60 results shown for Cylinder head.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: How my engine rebuild is going
    Historical mailing list - Dennis Haynes
    Sun, 16 May 2004 17:38:11 -0400
    ...Also when the gasket did fail, either the head, cylinder, or both is damaged. These surfaces need to be inspected and measure very carefully...
  • Re: Is this question just too stupid?
    Historical mailing list - Jim Cochran
    Sat, 30 Aug 2008 17:46:49 -0700
    ...That is > the job > of the top metal gasket between the cylinder and the head. The o- > ring is > there to keep coolant away...
  • Re: Ignition switch replacement Experience?
    Historical mailing list - Jerry Baker
    Tue, 27 Nov 2007 18:05:30 -0600
    ...Basically the lock cylinder has to be removed to gain access to the ignition switch. The ignition switch is attached to the lock cylinder...
  • off with her heads
    Historical mailing list - Tom Carchrae
    Sun, 6 Oct 2013 12:17:49 -0700
    ...I'm now faced with the typical cylinder stuck to head issue, and after some tapping and poking with the tools I had on...
  • Dripping '86 Vanagon
    Historical mailing list - Michael Harris
    Wed, 22 Nov 1995 15:56:13 -0800
    ...coolant from the bottom of the passenger side cylinder head. OK - sounds bad, maybe new head gaskets needed?? The strange thing is that it...
  • Re: Ignition - 2.1L wasserboxer, 1991 Carat
    Historical mailing list - Karl Wolz
    Sun, 28 Sep 2014 14:09:12 -0700
    ...I'm all ears! > > Also - could anyone tell me the proper plug length to be screwed in to a > cylinder head. > > Thanks > > John the...
  • Re: Which Subaru engine?
    Historical mailing list
    Thu, 17 Jul 1997 19:25:39 +0000
    ...Plus the XT6 heads had a rep for problems. IMHO it would be damn hard to beat the loads of early Legacy 4 cylinders...
  • Re: Air in my coolant - part deux
    Historical mailing list
    Tue, 19 May 1998 15:56:19 -0400
    ...Someone on the list stated that sometimes these leaks only manifest thmselves when the engine is under load (like doing 65 with a headwind...
  • Re: 196,000
    Historical mailing list - Mark Drillock
    Fri, 10 Mar 2000 09:45:25 -0800
    ...This motor has a different - block, crank, pistons, rods, head, manifolds, entire FIsystem,etc- than the Audi 5 cylinders sold in the USA. Guess...
  • Re: Mileage-stone
    Historical mailing list - Jim Felder
    Thu, 8 Dec 2005 20:13:52 -0600
    ...original crosshatching is clearly visible in my cylinders. If there's nothing wrong with the heads to speak of, would it make sense to...
  • Round Headlight Buckets: Galvanized Steel?
    Historical mailing list - neil n
    Fri, 22 Apr 2011 09:41:59 -0700
    ...Thanks, Neil. -- Neil Nicholson '81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/ http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder...
  • Alternative Instrumentation
    Historical mailing list
    Thu, 18 Apr 1996 16:08:17 -0800
    With all this discussion about instrumentation, ie Cylinder Head Temp, Oil Temp, Oil Pressure, etc. I'm wondering if anyone on this list has...
  • Cylinder Heads 1970 cc Engines
    Historical mailing list - Archie J. Lopez
    Wed, 26 Jun 1996 21:09:19 -0700
    have you folks heard about the condition which causes burning of the valves due to loose valve guides, caused by "poor octane" ratings in...
  • Re: Who is it?
    Historical mailing list - The Bus Depot
    Mon, 6 Aug 2001 07:19:57 -0400
    ...of a slave cylinder. We give an additional 5% discount to listmembers on all orders over $50, excluding engines/transmissions/heads, special-order/made...
  • Coolant Pipes needed!!!!!!
    Historical mailing list - Chad G
    Fri, 26 Apr 2002 10:53:15 -0400
    ...another steel pipe (via a short rubber hose) to the right cylinder head. I'm experiencing some coolant leakage when the van is fully...
  • Ceramic Engines
    Historical mailing list - John Rodgers
    Thu, 22 Aug 2002 08:36:38 -0500
    ...I can just see my new 2.1L now with ceramic heads, ceramic valves, cylinder barrels, and pistons!!! Check it out. John Rodgers 88...
  • Aircooled Cylinder Head Temps - first observations
    Historical mailing list - Mike Rouby
    Sun, 24 Dec 2006 14:28:26 -0800
    Took my second camping trip in my 82 Westy ever. This time around I had a CHT guage added. On the highway it would...
  • Re: Front outer CV on Syncro
    Historical mailing list - Scott Maurer
    Thu, 21 Nov 1996 18:47:24 +0000
    ...I stripped the upper #4 cylinder head threads for the exhaust. (A mechanic said to remove and check my thermostat's opening temperature with...
  • Re: compressing piston rings in engine
    Historical mailing list - JRodgers
    Tue, 10 Dec 2013 08:29:44 -0600
    ...out before pushing the cylinder all the way > down. I just now plan to pull the pistons whenever the heads come off. Only > adds...
  • Re: quick and dirty head swap-dennis' 2 cents.
    Historical mailing list - Stuart MacMillan
    Thu, 23 May 2013 09:30:28 -0700
    ...little o-ring at top of cylinders is expected to do much. The combustion sealing ring (in head) should keep the combustion from the...
  • Re: WTB: One round headlight holdy-inny thing and screws, to '85
    Historical mailing list - neil n
    Sun, 18 Nov 2012 14:36:53 -0800
    ...http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines
  • Stripped threads in cylinder head, to fix?, now?, how?
    Historical mailing list - Sam Walters
    Wed, 10 Jan 2001 12:52:47 -0500
    ...This required removing one of the bolts that holds the front header to the cylinder head. The header must have been imperfectly formed and...
  • Pulling the engine out or not!! (Head gasket)
    Historical mailing list - Benny boy
    Wed, 5 Jan 2005 14:47:52 -0500
    ...gaskets replacement job by itself (lower sleeve ring, sleeve/cylinders removal, heads diagnostic, upper head gasket and rings, torque...) Tools needed, sealant.... i may...
  • Re: Changing the Black O Ring On a Cylnder Sleeve...
    Historical mailing list - Steve Cotsford
    Fri, 21 Feb 2014 09:35:55 -0500
    ...The piston starts off being fairly close to the top of the inside of the cylinder (TDC) before the cylinder gets pulled up just...
  • Re: <no subject>
    Historical mailing list - Nathaniel Poole
    Wed, 18 Oct 2006 17:45:32 -0700
    ...cylinder >> ridge and you can still see the crosshatch marks on the cylinder walls, >> oil >> galleries drilled and plugged. I know the heads were...
  • Re: VW Trends and Eurospec STILL LACK of power...
    Historical mailing list - John Rodgers
    Fri, 21 Jan 2000 16:47:29 -0600
    ...When the cylinders are in place, and the heads bolted on, the assembly forms the water jacket for keeping the cylinders cool. It is...
  • Re: cooling system diagnostic help? Long, lots of info about whats been done so far.
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 26 Apr 2010 14:03:31 -0700
    re Is there a way to check the integrity of a head/head gasket when the leak is not letting coolant into the cylinders...
  • '73 1700 rebuild
    Historical mailing list
    Mon, 26 Sep 1994 11:50:58 -0400
    ...We just fininshed installing the new rings & heads on my sister's 73 camper (1700cc type IV), and I got a couple of questions...
  • Re: Trouble getting WBX piston out
    Historical mailing list - Jim Felder
    Fri, 5 Oct 2012 07:20:08 -0500
    ...I also use a bit of lapping compound and lap the > > cylinders into the heads to get the top of the cylinders really clean...
  • Re: Head gasket sealant
    Historical mailing list - Frank Condelli
    Thu, 11 Jul 2002 07:30:34 EDT
    ...the head during warm up and cool down due to the expansion/contraction of the dissimilar metals used in the head, cylinders and water...
  • Type IV head removal
    Historical mailing list
    Tue, 25 Jul 1995 17:24:31 -0400 (EDT)
    ...What's happening is that the cylinders want to stay attached to the heads and not to the case (why is Muir so adament...
  • Re: ready to re-install cylinders/heads, but...problems..
    Historical mailing list - Stan Wilder
    Wed, 9 Apr 2003 13:15:38 -0500
    ...to boot... > Now gettng ready to reinstall, I slipped off the cylinders > and honed them, than attempted to pull out the piston pins > to...
  • Re: finding crack in Amsterdam, part 2
    Historical mailing list - Steve Williams
    Tue, 24 May 2016 01:05:15 -0600
    ...Alas, once the head came free > there was a visible crack all the way through the cylinder wall itself, > making the cracked head the...
  • Charge for Head Gasket Replacement
    Historical mailing list - Steve
    Tue, 30 Nov 1999 21:39:01 -0800
    ...The cylinder head was in great shape but the face of the block was slightly pitted.I used factory gaskets and head sealer and...
  • Re: Cooling system over pressurizing?
    Historical mailing list - Neil N
    Mon, 11 Jul 2016 14:14:26 -0700
    ...On Monday, July 11, 2016, Neil N <musomuso@gmail.com> wrote: > > > I think there is a leak between a cylinder and head and that...
  • 85 1.9 Thermostat Housing Leak
    Historical mailing list - Walter Houle
    Fri, 27 Apr 2012 11:20:27 -0400
    ...Its behind the flanged piece that contains the short hose connection to the cylinder head. I suspect corrosion is the cause. I checked my...
  • Re: Send in the Grounds...
    Historical mailing list - Karl Mullendore
    Thu, 17 Jun 1999 22:57:58 -0400
    On the left cylinder head, on top, and then also below the coil area on the body, depending on the year of the van...
  • oil pressure gauge sensor.
    Historical mailing list - james peters
    Fri, 2 Jun 2000 14:35:52 PDT
    ...After I had the heads and cylinders replaced the oil pressure gauge stopped working. The needle goes across the face and is buried to...
  • Re: repeatedly blowing head gasket
    Historical mailing list - Mike Collum
    Sun, 16 Mar 2003 19:32:36 -0500
    Maybe you could get someone who has a good head (no pun intended) to measure the depth of the area where the cylinder goes...
  • Fwd: exaust removal woes
    Historical mailing list - David Milo
    Fri, 13 Jul 2007 23:38:32 -0400
    ...For instance, if the head must come off, you should replace the cylinder hold down studs before installing the new head, due to stretch...
  • My Latest Purchase... Sometimes a DPO is a good thing.
    Historical mailing list - VW Doka
    Sun, 20 Jun 2010 20:49:26 -0700
    ...head gaskets. He based this diagnoses on the fact it ran on 3 cylinders, smoked and overheated. Poor running... plug wire for #2 cylinder...
  • what is bostig??, 1.9L still an issue
    Historical mailing list - Jonce Fancher
    Sun, 7 Aug 2005 22:17:51 -0400
    ...compression is 165 to 170 in all cylinders and injectors are perfect. im lost!!!! anyone in the ann arbor MI area got an idea...
  • Re: off with her heads
    Historical mailing list - Tom Carchrae
    Sun, 6 Oct 2013 15:06:57 -0700
    ...That helps > loosten the cylinders. The , with the head about a half inch off, hit it > HARD from all directions with a rubber mallet...
  • FS 75-78 Bus Parts
    Historical mailing list - Bill Minor
    Wed, 21 Aug 2002 19:00:15 -0500
    ...One pair 0220101-372-6 VW OEM Deep Recessed Oval Exhaust Port Cylinder heads, boy are these ugly. One looks to be OK and...
  • head stuck to cylinders
    Historical mailing list - Scott W.
    Thu, 25 Dec 2003 14:29:30 -0800
    ...I have used a 2x4 and a hammer to try and break the rusty barrels loose by taping around the head, tried prying on...
  • Re: Head temperature sensor
    Historical mailing list - Daniel Schmitz
    Fri, 1 Sep 2000 08:35:05 -0700
    ...Cooling air reaches all cylinders uniformly, unlike early Type 1 engines of the past. My VDO gauge spans 0 - 650 deg. F, and 350...
  • Re: 84 update/head job
    Historical mailing list - Tim Spotted Wolf
    Tue, 21 May 2002 11:37:37 -0400
    ...Today I removed the Left head (facing the back of vehicle. No problems! no broken bolts , studs or knuckles. Once removed I could see...
  • Re: 91 Westy - Mysterious Clutch/Transmission Problem Clutch driven, (Slave) cylinders.
    Historical mailing list - Wes Neuenschwander
    Tue, 5 May 2015 09:48:46 -0700
    ...91 Westy - Mysterious Clutch/Transmission Problem Clutch driven, (Slave) cylinders. Over the years I have replaced many of these cylinders and seen many different...
  • Re: 2.1 strange running before and after head gasket repair
    Historical mailing list - Jim Felder
    Tue, 13 Nov 2012 15:02:24 -0600
    ...The head gaskets leaked and the thermostat > housing was warped, primarily, but I had some other troubles along the way > like a cylinder frozen...
  • Re: Watching Oil Temp (long, as usual)
    Historical mailing list - Rocket J Squirrel
    Tue, 19 Jul 2011 17:24:07 -0700
    ...heads ie the roof of the combustion > chamber, the valve seats, the exhaust valve guides and ports and the > outside of the cylinder liners...
  • Re: Brake troubles - need opinions...
    Historical mailing list - Richard Golen
    Fri, 6 Oct 2000 09:57:18 -0700
    ...the headlight >switch, is on - like the hand break is engaged. > > From the feel of things, replacing pads, drums, rotors, calipers, wheel >cylinders, may...
  • Head gasket again...
    Historical mailing list - Richard Bias
    Tue, 14 Mar 2000 06:00:19 PST
    ...I cleaned the heads and the cylinder barrels myself. I was extremely careful to do a precise job, took close to a month, with...
  • Re: Update - Engine Cranks but No Start
    Historical mailing list - Wrenold Williams
    Sat, 2 Apr 2016 16:11:12 -0400
    Update: �Engine Cranks but No Start!� Finally got a used ECU from a friend and tried it after allowing the cylinders to dry out...
  • interesting generator motor
    Historical mailing list - Daniel Stevens
    Wed, 22 Oct 2003 16:09:42 -0400
    ...A boiler-type burner heats the outside of the cylinder heads of the engine to about 700�C. Pressurized nitrogen contained in the water...
  • Re: vanagon winter maladies
    Historical mailing list - David Beierl
    Wed, 24 Nov 2010 21:55:20 -0500
    At 06:14 PM 11/24/2010 -0800, Alistair Bell wrote: >cylinders. Anyone else have bets on other items? Yeah. I bet I don...
  • Re: AMC Cylinder Head Question
    Historical mailing list - Karl Mullendore
    Thu, 13 Dec 2007 23:35:29 -0500
    I would have someone else sit in the driver's seat while the engine is running and tranny being engaged (forward only!), then look...
  • Re: Turbo overboost (from digester)
    Historical mailing list - Don Hanson
    Wed, 2 Jul 2008 13:42:41 -0700
    ...of their headgaskets..A frequent problem with the 944 turbo racing crowd. It is common to see those small four cylinder motors putting out...
  • Re: Header bolts broken
    Historical mailing list - Cullen Stewart
    Tue, 26 Aug 2008 17:14:52 -0400
    ...Header bolts broken >I once had to put helicoils in the exhaust header holes for #1 cylinder > with the engine in the van. At...
  • Re: First trip with to be named Vanagon - some "excitement"
    Historical mailing list - Greg Potts
    Wed, 3 Sep 2008 11:43:10 -0400
    Hi Frank, On the type4 engine the cylinder heads will be damaged by excess heat long before the oil heats up. CHT is the...
  • Fw: Head Problems (87 GL) How bad is it.
    Historical mailing list - Jen & Rog Johnson
    Tue, 26 Jan 1999 19:47:51 -0600
    ...head gasket seal - meaning the pressure is introduced into the cooling system from one or more of your cylinders. In my case #1 cylinder...