Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 36+: 60 results shown for Engine idle speed.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: anyone with a 1.9L wbx advanced the timing???? as a performance mod?
    Historical mailing list - Chris Stann
    Wed, 30 Jan 2002 08:23:42 -0600
    ...Aside from a slightly elevated (but very smooth) idle speed I haven't noticed any side effects that would indicate any engine life shortening...
  • Re: unexplained power loss - help!
    Historical mailing list - Greg Potts
    Fri, 20 Apr 2007 07:20:14 -0400
    ...A bad coil can cause power loss under high load conditions but still work fine at idle and lower speeds. Happy Trails, Greg Potts...
  • Re: Last gasp: low compression exhaust valve can't pass smog
    Historical mailing list - Roland
    Wed, 26 Jan 2011 10:37:22 -0800
    ...The summary: - 2.1 WBX wouldn't pass smog, failed hydrocarbons at idle. The most likely reason it was missing; due to low compression...
  • Re: On the topic of Battery explosion/voltage reg Batt & Charging Discussion by SDF
    Historical mailing list - Scott Foss - Shazam
    Mon, 2 Jun 2008 11:05:58 -0700
    ...turns faster than engine speed you might notice, looking at the relative pulley sizes ) . It should read the same at idle as at 2...
  • Re: Electric Power Steering
    Historical mailing list - Dave Mcneely
    Thu, 23 Jul 2015 21:55:56 -0500
    ...Generally they spin at close to 1.5 to 2 times engine speed. What works at idle will not works as well at 16...
  • Re: New van Style
    Historical mailing list - Stephen Overmyer
    Wed, 7 Feb 2007 14:58:20 +1100
    ...same torque off idle as a boxer, but once on their way they will outperform the WBX on top speed and hill climbing. and...
  • Re: vanagon Digest - 14 Nov 1999 to 15 Nov 1999 - Special issue
    Historical mailing list - kenneth d lewis
    Tue, 16 Nov 1999 21:06:39 EST
    ...One member explained his Vanagon was running rich at idle but OK at >speed >based on his failed smog test. Another member suggested this...
  • Re: good new fuel tank source?
    Historical mailing list - Anthony Kimmons
    Sat, 21 Jul 2007 13:56:29 -0500
    ...the wbx engine, and remember the > volume was a bit low, but not a lot. Fuel pressure static and at idle is > ok right...
  • Re: Arduino and Vanagons
    Historical mailing list - James Eaton
    Wed, 13 Nov 2013 23:23:34 -0500
    ...the electronic cycle) to allow more air into the engine when the idle speed drops. Inputs include an AC sensor, power steering pump sensor...
  • Cut out problem fixed on 85 Vanagon
    Historical mailing list - Curtis Graham
    Thu, 4 Feb 1999 12:23:08 -0700
    ...It happens while idling at a stop light, at freeway speeds, or driving in town. The engine runs very well before and after this...
  • Re: Coolant Hoses, Complete Set -- Remove and Replace
    Historical mailing list - Gabriel Hourtouat
    Fri, 26 Jun 2020 01:05:47 -0400
    ...Replace pressure cap, let engine return to idle and you should be good to go. If the system is working properly it will finish...
  • Re: Stuck in Alturas with electrical mystery
    Historical mailing list - Jack R.
    Mon, 24 Sep 2007 08:58:57 -0400
    ...at half speed the indicator (alt and O2)lights will flicker a bit, at full rpm, they stay on steady. At idle...they go...
  • Re: Another trip to SWFL
    Historical mailing list - Robert Clemmer
    Mon, 21 Oct 2013 08:06:26 -0400
    ...Lowest it has ever gone when engine is at speed is 35 lb. Idle oil pressure holds 10 lb. even at the higher temperatures...
  • FS: Vanagon engines, tires, tranny, interior parts
    Historical mailing list - Sean Solowiej
    Tue, 15 Apr 2003 17:33:02 -0400
    ...And the idle stabilizer. And p/s pump and a/c compressor. And the cut-out engine wiring harness, all for '90 2.1L...
  • Re: Electric Power Steering
    Historical mailing list
    Fri, 24 Jul 2015 19:45:53 -0400
    ...Generally they spin at close to 1.5 to 2 times engine speed. What works at idle will not works as well at 16...
  • Re: Hydraulic Lifter noise ?
    Historical mailing list - Gabriel Hourtouat
    Tue, 11 Sep 2012 01:53:48 -0400
    ...loud ticking emanates from the right side of the engine. >> If we let it idle for 5-10 minutes, the sound slowly disappears. >> >> We...
  • Re: Weird Coolant System Behavior
    Historical mailing list - Per Lindgren
    Sat, 12 Feb 2000 02:31:15 +0100
    ...You speed up the circulation, the cold coolant comes to the engine before the temp levels out. Seems to make sense. PerL 87 Syncro...
  • Re: 88 vanagon gl "issues"
    Historical mailing list - John Rodgers
    Wed, 14 Feb 2007 16:40:19 -0600
    ...engine off, Then disconnect the wire at the end of the idle stabilizer valve(ISV). Start it back up and check the idle speed...
  • Weird things happen ......
    Historical mailing list - Calle Fallberg
    Tue, 28 Nov 2000 10:41:09 +0100
    ...I found out that for the first time since I bought the Van, the idle was a steady 800 rpm! And this is even...
  • Re: question regarding clutch bearings and shifting problems
    Historical mailing list - Carrington, Tom
    Mon, 9 Jun 2003 01:13:44 -0400
    ...engine > > > with the gear shift in neutral and just let it idle? > > > > > > > > > > > ________________________________________________________________ > The best thing to hit the internet in years - Juno SpeedBand! > Surf...
  • Looked at 86 Westy Wolfsburg Today.......
    Historical mailing list - Anthony L. Mourkas
    Fri, 20 Apr 2001 00:06:34 -0400
    ...3 speed. Engine blew a head stud and spewed coolant and was towed to present location. Engine started right up and idled beautifully for...
  • Re: Different Kind Of Valve Adjustment Question? NOW What's next?
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 28 Jul 2008 20:18:38 -0700
    ...Resuming to highway speeds > cools things back down to normal. > 2. Engine power is not great and the motor will not idle under most...
  • Re: Thermostat soup: A comparison.
    Historical mailing list - Robert Fisher
    Wed, 20 May 2009 20:58:12 -0700
    ...Another possibility is that a prior water pump failure damaged the engine case and reduced capacity at low speed is the result. Dennis -----Original...
  • Re: oil light
    Historical mailing list - Christophe Guilbert
    Mon, 2 Oct 2017 10:33:05 -0700
    ...When you accelerate , you build up oil pressure and that's Okay , that's when you idle or go low low speed that you...
  • Re: Lube the accelerator cable on a vanagon?
    Historical mailing list - Alistair Bell
    Thu, 13 May 2010 22:00:15 -0700
    ...the engine and the pedal in the cab without much improvment. This is an 84 manual tranny van. When I go 'off-idle' without...
  • Oil pressures in 1.9? Daily driving a Westy?
    Historical mailing list - Stephen Steele
    Fri, 29 Sep 2000 13:24:40 -0400
    ...engine with over 125K miles, what would be acceptable oil pressure at idle and at fairly high ambient temperatures? And... at cruising speeds...60mph...
  • '82 diesel, Ring job
    Historical mailing list - Robert Crawford
    Sat, 22 Feb 1997 16:09:51 -0800 (PST)
    ...Then about a month ago it suddenly jumped to apx 25mi/quart and when I ran up the engine speed, the oil backed up...
  • Re: Side Air Intake Engine Cooling Question (searched)
    Historical mailing list - Jake de Villiers
    Tue, 27 Jul 2010 14:39:07 -0700
    ...engine consistently: > > - throws coolant sensor error code: 'Intermittent short to ground'. > - turns MIL (check engine) light on at highway speeds > - hunts at idle when...
  • Yet ANOTHER idle update!
    Historical mailing list - Marc Perdue
    Mon, 14 Apr 2003 21:20:07 -0400
    I know you've all been hanging on the edges of your seats waiting for yet another idle update (NOT!), so here it is...
  • Re: Alternator out at *high* rpms?
    Historical mailing list - Dennis Haynes
    Mon, 8 Dec 1997 20:46:06 -0500
    ...Oddly enough, if I let the engine cycle down >towards idle (clutch in, foot off of gas pedal, goin' downhill) something >went right, and...
  • Re: Timing proceedure: 2.1 Watercooled; Bentley page 28.42 Digifant.
    Historical mailing list - John
    Mon, 20 Sep 1999 13:19:17 -0400
    ...1) Warm the engine to >80*C oil temperature (full hot). 2) At idle speed (~800 RPM), align the timing mark on the pulley...
  • Re: Still lousy gas mileage
    Historical mailing list - Dennis Haynes
    Wed, 2 May 2012 18:03:51 -0400
    ...While over advancing the timing make it idle better, seem more responsive at low to mid speeds and make you think it is running...
  • Re: So my stepson asks . . .
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 20 Aug 2012 21:03:06 -0700
    ...1 idled properly, didn't surge, had even and higher >> compression, > Interesting points to make in a DEFENSE of the waterboxer engine ......... . > > So, you...
  • Zetec Install Pics
    Historical mailing list - Peter T. Owsianowski
    Tue, 19 Jan 2010 19:55:56 -0500
    ...The motor fired up ran perfectly except for a fast idle at 1900 rpm. Readajusted throttle valve body at a switch. Now idles at...
  • Re: Fuel consumption in different gears - how does the energy / fuel work?
    Historical mailing list - Daryl Christensen
    Sat, 24 Mar 2012 19:28:33 -0700
    ...speed the engine must have a minimum amount of fuel, so this question may not apply to really low speeds or at idle. Again...
  • 1.9 TD performance upgrades prove successful: 95 mph??
    Historical mailing list - Karl M.
    Mon, 4 Jun 2001 01:19:31 -0400
    ...pressure off idle, and denser air, things should become interesting! This 'little' diesel is turning out to be quite the impressive engine, much more...
  • Bucking vanagon again
    Historical mailing list - Airic
    Sun, 7 Jan 2007 15:01:15 -0600
    ...about 1/2 throttle position it bogs down, driving or sitting with a spare temp sensor two installed, o2 sensor disconnected, idle regulator bypassed...
  • Am I Crazy, Sane or Dreaming? re: Surging
    Historical mailing list - Bruce Ralphs
    Tue, 19 May 1998 22:54:46 -0700
    ...I also thought I'd disconnect the two leads running into the idle stab (square mounted on drivers side of engine bay just ahead...
  • Re: vanagon trans slipping
    Historical mailing list - Daniel Rotblatt
    Tue, 25 Oct 2011 13:09:25 -0700
    ...Seems to slip sometimes when slowly speeding up at low speeds - around 10 MPH - and sometimes more on turns (maybe right turns?). General shifting...
  • Re: vanagon Digest - 1 Nov 2002 - Special issue (#2002-1293)
    Historical mailing list - Jay L Snyder
    Fri, 1 Nov 2002 15:52:21 -0500
    ...The high idle speed may be correct since the > ECU thinks the engine is cold. The most likely suspect is the thermostat. The needle...
  • Re: Tight valves!
    Historical mailing list - Matt Sim
    Thu, 14 Jun 2001 20:35:31 -0400
    ...If you have the same transmission, the rpms of the engine can't possibly change for the same speed. Matt ----- Original Message ----- From: Robert...
  • UPDATE Re: Oil Pressure System Confusion...
    Historical mailing list - Ryan
    Sun, 1 Jul 2007 15:33:17 -0400
    ...the .9 bar wire and rev the engine.....nothing. Since my tach doesnt work, my speedo is held on with one screw, and a...
  • Re: Fuel consumption in different gears - how does the energy / fuel work?
    Historical mailing list - Dave Mcneely
    Sun, 25 Mar 2012 13:07:30 -0500
    ...speed the > engine must have a minimum amount of fuel, so this question may not apply > to really low speeds or at idle. > > Again...
  • For Sale - Upstate New York area- 2.1 rebuilt engine, associated parts.
    Historical mailing list - Road Trip
    Fri, 5 Dec 2003 13:05:59 -0800
    ...2.1 liter factory rebuilt engine with approx one year use. This is one of those motors you used to be able to buy...
  • Re: Limited high coolant temps
    Historical mailing list - Bill Shawley
    Sun, 10 Aug 2008 12:03:58 +0000
    ...At highway speeds, the needle is just to the right of the> > LED, or bit more. If the van is allowed to idle too...
  • Re: Lube the accelerator cable on a vanagon?
    Historical mailing list - Don Hundt
    Fri, 14 May 2010 22:29:38 -0400
    ...the engine and the pedal in the cab without much > improvment. This > is an 84 manual tranny van. When I go 'off-idle' without...
  • Re: Aux Air Flow Regulator
    Historical mailing list - David Beierl
    Mon, 29 Jul 2002 13:33:12 -0400
    ...idle speed changes when squeezing the hoses per >Bentley test. This is the old style regulator that mounts on top of the >engine beneath...
  • Re: Read your manual: Oil pressure nonsense
    Historical mailing list - David Bohannan
    Wed, 13 Sep 2006 14:41:22 -0400
    ...speed travel, the > oil will stay coolest near the the lower mark to halfway. More is not > better. > > Also, the 1.9 liter engines...
  • Re: '88 GL - Gradual Power Loss
    Historical mailing list - Joel Cort
    Tue, 27 Mar 2012 05:24:34 -0700
    ...Hills > Cop), etc. > > 1) Power loss - Worse at speed, wont notice much when free wheeling engine > 2) Funny exhaust sound (somewhat of a "Hissing...
  • Re: 2.1 strange running before and after head gasket repair
    Historical mailing list - Dennis Haynes
    Tue, 13 Nov 2012 21:23:02 -0500
    ...Any high resistance in the wiring is an issue especially with this sensor being shared with the idle speed controller. Dennis -----Original Message----- From...
  • Re: peed sensor (subie conversion question)
    Historical mailing list - Chuck Mathis
    Tue, 7 Jul 2009 21:45:31 -0500
    ...vanagon speedo ) .....and that's not suppossed to really work > that > well, but it sure ran great ! > Idled great, everthing ..........so your engine may...
  • Re: Runaway Engine RPMs
    Historical mailing list - Scott Daniel
    Thu, 10 Oct 2013 14:03:17 -0700
    ...About 3/4 of the way >> the low speed fan came on as expected. A minute later the engine revved up >> tp 3K rpm...
  • Re: coolant leak after long idle
    Historical mailing list - Dennis Haynes
    Tue, 26 Jun 2007 09:01:39 -0400
    ...coolant leak after long idle >Date: Sun, 24 Jun 2007 22:36:11 -0400 > >The replies I got from the list proved correct, changing...
  • Re: master brake light misbehaving
    Historical mailing list - brett rueff
    Mon, 19 Jul 2010 13:09:43 +0000
    ...It is not speed related - I can do it at idle. The more I am above 3000rpm the stronger it comes on. I have...
  • Re: Need input on radiator problem
    Historical mailing list - benoit
    Tue, 6 Feb 2007 23:58:23 -0500
    ...by the way) > >The engine/coolant don't overheat at low speed, only on big hills wile >climbing, the engine sound and run fine...
  • Re: Oil pressure guage
    Historical mailing list - Frank Condelli
    Wed, 26 Sep 2001 07:10:11 EDT
    ...With 350,000 km on original engine shows 7 lb. pressure at idle and 30 ~ 40 lb. at highway speeds with thoroughly warmed engine...
  • Re: Coolant into the bleeder screw hole?
    Historical mailing list - neil N
    Sun, 12 Oct 2008 16:27:28 -0700
    ...it was too full, I revved the engine for a bit, let it come to idle, and some coolant came out the top. Other...
  • Hesitation
    Historical mailing list - Tim Belanger
    Fri, 11 Feb 2000 14:02:36 EST
    ...It will go up to like 1500 RPM's as I leave a light or stop sign and just drop to idle speed RPM...
  • Re: More Conversion engine stuff.
    Historical mailing list - Greg Potts
    Thu, 3 May 2007 12:32:58 -0400
    ...Tune the bike engine to idle at 1500 RPMS and you still have a 750 RPM take-off speed at the transmission, a little...
  • Re: Curious Hesitation
    Historical mailing list - Evan Mac Donald
    Sat, 17 Dec 2005 18:13:21 -0800
    ...Sometimes, at sustained highway speeds, with a well tuned engine, the temp at the probe is not enough to keep the readings (voltage output...