

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 31+: 60 results shown for pressure test.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- how to perform a leak down???Historical mailing list - Street BugsWed, 11 Dec 1996 02:22:04 GMT...can i perform a leak down test? i was checking out my compression tester this past weekend and notice that it disconnects from the...
- Stumped-Runs Rich/StallsHistorical mailing list - Aileen BoydFri, 13 Jun 2008 20:08:00 -0400...Tested 02 sensor-ok New Temp II Sensor Replaced Idle Stablizer Unit Replaced ECU New Fuel Pressure Regulator New spark plugs and wires All...
- Re: start - won't sart - solutionHistorical mailing list - mark drillockFri, 22 Aug 2003 23:06:51 -0700Check the fuel pressure regulator carefully. They can fail in more than one way. One way that may fit your problem is that they...
- Re: Missing coolantHistorical mailing list - Eric WunrowThu, 15 Oct 2015 22:05:11 -0600...They rely need to be tested >> in place with a gauge set up so you can confirm the opening pressure. >> Since the Vanagon uses...
- Re: Tranny oil change: How to *not* do it.Historical mailing list - Stuart MacMillanTue, 1 Feb 2000 13:24:28 -0800...It had been a cold, crisp morning > when I test opened the fill plug. At that point I had pressure equalized > the tranny to...
- Re: permanent fuel pressure gaugeHistorical mailing list - RaceingcajunMon, 6 Mar 2006 06:33:08 -0600...And now you purpose to do the same thing on an Audi CIS system, running full working pressure of 75 lb's to 85...
- Re: fuel pressure test connection size?Historical mailing list - Bill DavidsonTue, 6 Feb 2001 17:14:08 -0800> As one who has the Digitool permanently mounted, I like this idea. You could pop the lid and get an instant read of things...
- Update on the '83 I was looking atHistorical mailing list - Standley, CraigFri, 20 Jul 2001 15:16:18 -0800...It also failed emissions, and it was a little slow to pump up pressure during the compression test on the #1 cylinder. The mechanic...
- Re: coolant...Historical mailing list - JimThu, 29 May 2003 16:56:22 -0700...the plugs right off.) Jim MICHAEL POPE wrote: >well the pressure was tested at idle and at about 2,000 rpm- mech(old owner...
- AMC HeadsHistorical mailing list - Kim SpringerFri, 11 Jul 2008 20:43:12 -0700...So we pressure tested them, good. But they will need 4 new valves and 4 new seats and probably guides. I'm deciding what...
- Re: diesel fuel injectors???Historical mailing listMon, 13 Jan 1997 20:12:11 +0000...Leakage test for injector: Should hold 110bar / 1595 psi for 10 seconds without leakage. Opening pressure: 1740 - 1885psi (used) 1885 - 2001psi (new) The shim...
- of oil lights and pressure switchesHistorical mailing list - Charles McGeheeTue, 25 Sep 2001 18:10:51 -0700...how many oil pressure switches does a 1985 wbx have and how can I tell if the part store sold me me right one...
- Follow up Q Re: fuel pump behaviour with ignition onHistorical mailing list - Jeff OxroadFri, 19 May 2006 14:08:01 EDT...Is there a pressure sensor that shuts off the pump when the correct fuel pressure is reached OR is it a timed power spurt...
- Re: Oil pressure -- normal range?Historical mailing list - Scott Daniel - TurbovansSat, 9 Apr 2011 16:23:50 -0700...the 0 to 100 psi gauge. >> On one engine I tested, oil pressure was as high as 60 psi cold, and as >> low >> as...
- Re: Let's fix our Dometic refigeratorsHistorical mailing list - Mark DrillockSat, 22 May 1999 18:34:52 -0700...I think that the difference in performance may be due to the pressure of the propane. The tank has a 2-stage regulator that...
- Re: Oil Pressure = 0Historical mailing list - Sudhir DesaiSat, 23 Dec 2006 16:33:58 -0500...to get to in > order to attach a temp oil pressure gauge for test and check purposes. I > started the motor and the lifters...
- Re: Definitive test for Hall > ECU?Historical mailing list - Ken WilfordTue, 30 Oct 2007 07:21:50 -0400...If the valves adjustment is too tight this can cause low manifold pressure (vacuum) and idling problems. A compression test would help in this...
- Running issue improvementHistorical mailing list - Eric CaronThu, 29 Sep 2022 11:05:58 -0400...pressure, other wires, and injectors but all were good. Spark plugs were clean after he ran the van for about 40 miles of test...
- Re: Cooling questions stillHistorical mailing list - Benny boyThu, 20 Sep 2007 22:14:22 -0400...So, that said, people here forgot how to test that system: http://www.benplace.com/pressure_test.htm So bring that sheet/page to...
- Re: Coolant StrangenessHistorical mailing list - Scott Daniel - TurbovansMon, 22 Aug 2011 11:46:44 -0700...right now, with no further information or test results.. it sounds like .. either pressure cap is not holding pressure properly ..... or cooling system pressure...
- Re: Antifreeze in combustion chamber...Historical mailing list - Bob DonaldsSat, 27 Nov 1999 15:13:09 -0500...warm up the stray coolant could be what your seeing next pressure test the cooling system the green oring does not stop the coolant...
- Re: Dometic Fridge: Bah Humbug! <grin>Historical mailing list - neil nThu, 12 Aug 2010 12:29:59 -0700...Pressure > > - The article Mark wrote really helped. If you understand how to use the tools, it's easy to set up a test. (especially...
- Tencentlife Oil CoolerHistorical mailing list - Dave McneelyFri, 8 Apr 2011 11:17:34 -0500...But, since the pressure gauge has always showed good pressure, around 40 psi, under winter conditions, or in summer if it is reasonably cool...
- Re: coolant pressure guageHistorical mailing list - David BeierlSat, 23 Oct 1999 12:22:19 -0400...There must be some pressure drop across the system when the pump is running, though, so you'd get an RPM-related pressure change...
- Re: Oil Pressure Light on-need help! (dealer cant fix it)Historical mailing list - Scott Daniel - ShazamFri, 4 Apr 2008 21:32:52 -0700...OIL PRESURE TEST, very simple! that is the basic stuff to do first, eliminate the worse case... maybe the oil pressure is low! Second...
- Re: 1.9L Gutless when first startedHistorical mailing list - Geza PolonySun, 21 Oct 2007 16:39:27 -0400...I pulled the coil wire out of the >dizzie and did my testing. > >About four days later someone who knows a lot about working...
- Re: Nitrogen in tires (was:Michelin Tire Experiences)Historical mailing list - DenmiesterFri, 8 Dec 2006 18:28:45 -0500...In the test lab we put 4 used DC-9 tires (scrap tires that were considered worn out by the airline) on our drop...
- Re: what clues about engine health can I get...Historical mailing list - Chris S.Tue, 15 May 2012 17:22:16 -0400Oil pressure gauge is a good start, but you also need oil temp, since the two are very closely related. Half the information is...
- Re: Checking pressure cap function???Historical mailing list - Jim FelderMon, 29 Jul 2013 11:57:19 -0500I took a bad coolant cap and a short piece of hose and made a tester. It works fine for what it can do...
- Re: compression testing procedureHistorical mailing list - Don GibbonsTue, 28 Apr 1998 09:52:50 -0400...As long as everyone does it the same we get a meaningfull test. With the throttle open the engine will "pump up" pressure slightly...
- Re: what steps can be taken to diagnose head gasket problems?Historical mailing list - PeterMon, 31 Jan 2005 15:47:54 -0800...What should I ask him to look for? > My thoughts: > -Compression Test > -Leak-down Test > -Cooling system pressure Test > -Visual inspection(of what?) > > The...
- Re: oil inside intake bootHistorical mailing list - Eric ZenoTue, 4 Jan 2005 10:22:07 -0500...This pressure is uasually a sign of bad rings allowing to much combustion gas past the rings. Do a compression test. This will determine...
- Re: 87 Vanagon- Antifreeze smellHistorical mailing listThu, 24 Oct 1996 16:02:14 PSTVic; If you want to test the core pinch off the lines then remove them from the core. The core can then be slid...
- Crummy Vanagon performanceHistorical mailing list - Richard KoernerSat, 15 May 2021 02:25:22 +0000...Disconnect fuel line from Fuel Pressure Regulator outlet; Connect to pressure gauge; Test: Set Ignition to run without cranking Engine to run Fuel Pump...
- Re: Dometic won't light troubleshootingHistorical mailing list - mdrillockThu, 17 Jul 2008 10:06:04 -0700...If the stove is connected you should light both burners on medium flame while checking the pressure assuming you can connect the test device...
- Re: Dometic Fridge: Bah Humbug! <grin>Historical mailing list - neil nWed, 11 Aug 2010 10:09:37 -0700...I did not check the pressure. I built a manometer a while back but in the article, Mr. Drillock shows a way to test...
- Re: Wobbly Still Won't Go... Gurus pleassssse heeellllllppppp...Historical mailing list - Scott and NormaSat, 20 Jul 2002 22:27:53 -0800...Cap the > pipe again and up goes the pressure. What you'll be doing with the test > light is following along the pipe, looking...
- Fuel leaking from Sender Unit on Replacement Fuel TankHistorical mailing list - Richard KoernerWed, 19 Oct 2016 18:59:23 +0000...flat a surface as possible. The leaking stopped (he pressure-tested and smoke tested)...but has now re-appeared when filling the gas tank...
- Re: Start up,back fire?Historical mailing list - Dave McneelyTue, 19 May 2015 09:16:36 -0500...do the fuel leak down test is with a fuel pressure gauge. > >> Bentley says system should hold pressure (30 psi or so) for several...
- Re: 20 psi oil pressure on freeway. Worry?Historical mailing list - Craig Oda's Personal emailSun, 13 Oct 2002 15:17:21 -0700...1) compression test 2) engine flush with some engine gunk 3) straight 40w oil (maybe with some viscosity thickener like ring seal) I'm...
- Re: Freeze plug leaks oilHistorical mailing list - Roger VanTillSun, 24 Jul 2011 08:05:03 -0400...My > question > is; can it be fixed? Is it leaking because of oil pressure behind it, or > it's just oil being there without...
- Re: Have I damaged my control unit?Historical mailing list - Jeff OxroadSun, 6 Aug 2006 12:32:37 EDT...Anyway I'm gettting ahead of myself, because I have to run some basic tests like check fuel pump pressure, check if the grounds...
- Consistent cutout at 3k rpmHistorical mailing list - Jonathan PooleWed, 13 Apr 2011 00:33:10 -0400...with better power/feel than before these changes -fuel pressure was stable when tested it while making these changes. -engine temps are good (350...
- Re: Auto tranny questionHistorical mailing list - Bob DonaldsWed, 10 Jan 2007 11:00:32 -0500...The Bentley does detail pressure testing the trans to determine internal problems. An experienced tranny guy can also drop the valve body and air...
- Re: Resolved: Re: Oil pressure light comes on after about 7 minutes.Historical mailing list - RolandSun, 12 Dec 2010 17:31:08 -0800...Yes, but I have no way to check for this (that I > > know of) except the oil pressure test. This engine has been pretty...
- Re: Mobil I ... negative..(from digest)Historical mailing list - Mike SFri, 5 Oct 2007 14:20:54 -0400...37 API MT-1, No requirement These tests are for determining load-carrying, wear, and extreme-pressure characteristics of gear lubricants in axles under...
- Re: Cooling system woesHistorical mailing list - Malcolm StebbinsFri, 14 Dec 2001 12:04:34 -0400My experience with coolant problems leads me to believe that the cap on your coolant reservoir tank is not holding pressure. As long as...
- Coolant going from expansion into refill tank and overflowing refill tankHistorical mailing list - tabe johnsonTue, 25 Jan 2005 15:58:46 -0500...I watched the pressure when I started the engine. It didn't soar immediately. A compression test shows Cyl # Jan 2004 Jan 2005 1...
- Re: Dometic Fridge Servicing / RenovationHistorical mailing list - Richard A JonesSun, 26 Sep 2004 22:16:18 -0600...I had new regulators installed locally and they test the pressure as part of the installation. Keep us informed of what you do and...
- Rough Idle troubleshooting needHistorical mailing list - Steven MillsFri, 11 Sep 2015 15:37:24 +0000...So far, have tested with good parts ECM, AFM, Dist, plugs, plug wires, alternator, coil, fuel pressure/flow rate, idle stabilizer, cold temp sensor...
- Re: Heater removalHistorical mailing list - Gerald SkerbitzMon, 20 Feb 1995 13:18:55 -0600 (CST)...I don't have a VOM fine enough to test the resistor, but it's not open, so does that mean it's probably...
- Re: How best to JB weld pitted heads?Historical mailing listTue, 14 Mar 2000 07:32:41 EST...your heads down to a local machine shop and have them pressure tested. This will save you having to go through all the trouble...
- Oil tempsHistorical mailing listSun, 14 Apr 1996 23:32:22 -0400I've had about a week with temp and pressure gauges installed and I'm not much liking what I see. In light duty...
- Re: A Snow Story (Whoa-vanagon!!!) and Lessons LearnedHistorical mailing list - Ben TThu, 10 Jan 2002 22:18:37 EST...who have seen me testing a rear brake conversion on one of my cars. If you permit too much pressure to go to the...
- Re: 1991 Carat AC System servicingHistorical mailing list - John RodgersFri, 30 Sep 2016 16:32:13 -0500...would charge the system with nitrogen to test for leaks and also > see if the pressure switches work enough to at least get the...
- Re: Compression pressure figures?Historical mailing list - Carrington, TomWed, 15 Mar 2000 09:15:40 -0500...this 85 bus, water cooled) has > compression pressure of 105, 90, 100, 75 PSI. mechanic > > doing the test says it was rushed - didn't...
- Re: Oil buzzerHistorical mailing list - Dennis HaynesWed, 6 Apr 2016 22:00:50 -0400...Ultimately a good engine install would include oil pressure testing cold through hot and ten a compression-leak down test to establish the baseline...
- Air conditioning stumperHistorical mailing list - A J IFri, 20 Jul 2012 19:25:36 -0400...When the compressor is NOT on I can read pressure in the system but when I turn on the compressor the pressure goes to...
- Re: 4th heater core burst in 1 year!Historical mailing list - Mark DormThu, 5 Jul 2001 15:21:28 -0700Okay, how often are we supposed to change our pressure cap? If once a year maybe we could declare a certain date National Pressure...
- Re: Coolant pressure test... video.Historical mailing list - Michael SullivanTue, 15 Dec 2009 20:46:01 -0600anxiously waiting on part 2 :-) Michael in San Antonio 91GL AT 'Gringo' 73 Beetle On Tue, Dec 15, 2009 at 7:44 PM, Benny...