

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 28+: 60 results shown for Crankcase.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Re: 81' New Owner To DoHistorical mailing list - Stan WilderTue, 18 May 2004 23:17:11 -0500...Run the vehicle for about 300 miles with the Mystery Oil Mix in the crankcase. It is best to get this 300 miles around...
- Re: Crankshaft oil seal & holding that pulleyHistorical mailing list - Scott Daniel - TurbovansFri, 19 Dec 2008 13:18:51 -0800...possible contributing causes can be the crank is loose in the main bearings, or has excessive end play, and excessive crankcase pressure, from a...
- Re: Oil leak since rebuilt 2.1l installedHistorical mailing list - Karl WolzWed, 30 Jun 2010 15:09:13 -0700...a seal issue, or what the seal seals against |>> .....or breather/crankcase pressure issue. ...somewhere in there. Even |>> excessive main bearing oil clearnce could...
- Re: oil coolerHistorical mailing list - Max WellhouseTue, 1 Apr 2014 10:03:48 -0500...you'll have a lot of oil draining back into the crankcase at startup each time. One way valves cold solve that problem, but...
- Re: I'm rich, filthy stinking rich...Historical mailing list - kenneth d lewisTue, 18 Jan 2000 20:47:14 EST...Air is suck via the crankcase vent through the pushrod tubes. It would not idle , loped real bad. I envisioned the worst. Unfortunately someone...
- Re: Friday: New VW Engine--it's Miller (cycle) timeHistorical mailing list - Jim FelderFri, 29 Apr 2016 17:04:15 +0000...the microscope, and > now > > > > will make sure the water in the crankcase and engine remains > stationary > > > > while the car is warming up. As well...
- Re: rattle INSIDE engineHistorical mailing list - Al and Sue BraseThu, 8 Sep 2005 10:27:07 -0500...of hammering between the top of the distributor hole >in the crankcase and the distributor bracket. It is worn down there slightly >except for...
- Re: Rolling right along on my 'new' block (inline VW swap into Vanagon)Historical mailing list - Robert KeezerWed, 9 Jun 2010 12:12:14 -0700...This keeps the oil from sloshing up into the crankcase and skims off ecessoil on the crankshaft, helping to retain hp. � Robert 1982 Westfalia...
- Fwd: Re: Re: 2.1L Align bore and main bearingsHistorical mailing list - Zoran MladenWed, 3 Dec 2003 19:08:51 -0800...to > > > make that call later. > > > > > > My concern is align boring the crankcase and > then > > > deciding which bearings I > > > need. I did a search of...
- Rebuilds, was: Mechanic Horror StoriesHistorical mailing list - EMZWed, 12 May 1999 12:02:15 -0400...By the way the > first engine he shipped me had a shop rag left in the crankcase. It ran for > about 10 minutes until...
- Re: Comments on the Oil Cooler Upgrade IssueHistorical mailing list - Frank GrunthanerMon, 21 Nov 2005 03:06:06 EST...If the oil has been aerated in the crankcase and any significant amount of this aerosol is in the oil liquid mix, then the...
- Re: Not breathing rightHistorical mailing list - Steve BlackhamSun, 20 May 2001 22:04:21 -0600...I have disconnected the >> crankcase >> >> >> breather inlet, and aux air valve at the elbow but I still >> >> don't >> >> >> get what I consider good...
- Re: DJ-code WBX technical specsHistorical mailing list - Chris SSat, 20 Dec 2008 17:38:43 -0500...the DIS unit must be removed and > plugged together. > > Disconnect engine crankcase breather and plug on side of air cleaner. > > -- > Chris S. > Disclaimer: "Death...
- Re: Carb conversions?Historical mailing list - Sudhir DesaiWed, 16 Aug 2006 21:09:46 -0400...Excess NOx, burned > pistons. > > How about proper porting for 2 stage distributor advance? > Crankcase Breather the works? > Fuel Vapor control! > Air filter with adequate...
- Re: MY new '88 Westy, 53K orig. milesHistorical mailing list - John RodgersThu, 11 Nov 2004 14:20:01 -0600...On the oil, I would add a can of Marvel's Mystery Oil to the crankcase, drive it a bit then immediately change the...
- Re: Trip Report: 742 miles and a blown sealHistorical mailing list - Dennis HaynesSat, 21 Dec 2002 10:58:04 -0500...Make sure the crankcase vent lines are clear. If you only have the vent from the valve cover, you may want to add another...
- Re: Hard starting 84 vanagon - stumpedHistorical mailing list - Brian KeeseThu, 11 Sep 2003 14:58:58 -0500...He replaced the ignition switch relay, the main ground strap from the crankcase to the frame, and moved the grounds from the engine to...
- Re: DJ-code WBX technical specsHistorical mailing list - Chris SSat, 20 Dec 2008 17:19:24 -0500...the DIS unit must be removed and >>>> plugged together. >>>> >>>> Disconnect engine crankcase breather and plug on side of air cleaner. >>>> >>>> -- >>>> Chris S. >>>> Disclaimer: "Death...
- Re: Friday: New VW Engine--it's Miller (cycle) timeHistorical mailing list - JamesSat, 30 Apr 2016 22:53:23 -0400...the microscope, and now > > > will make sure the water in the crankcase and engine remains stationary > > > while the car is warming up. As well...
- Re: Oil Pressure light & buzzer, Yikes! Mystery # 1Historical mailing list - John RodgersSun, 11 Feb 2001 22:29:18 -0600Rob, The oil system high pressure switch is located at the bottom of the crankcase on the lower left side of the rear of...
- Re: Warming the oil in cold weather? Other options.Historical mailing list - Dennis HaynesSun, 3 Jan 2016 23:24:20 -0500...The vws had a circular thing >>>> under the centre of the crankcase. They also had a "battery blanket" >>>> to keep the battery warm. Vanagons...
- Re: Isolating an idle problem?Historical mailing list - Dennis HaynesSun, 21 Dec 2014 21:43:31 -0500...Oil in the intake track is a sign of excessive piston blow-by or a crankcase venting problem. As for the idle going down...
- Re: Timing IssuesHistorical mailing list - Alistair BellSun, 29 Dec 2013 18:02:45 -0800...So, at idle, everything hooked up and engine warm, if you point your Flintstones timing strobe at the crankcase center seam, you'll see...
- The Misadventures of Vanagon Stan. Long, LongHistorical mailing list - Stan WilderWed, 19 Jun 2002 07:03:49 -0500...After checking the oil (what oil?) and finding none in the crankcase I get into my emergency stores and add a quart. Well, I...
- Re: (fryday stuff)Top 20 Why Reasons Round headlight vans are betterHistorical mailing list - Shawn WrightFri, 3 Jun 2005 18:10:17 -0700...Liter rebuilds are cheaper to obtain because they have an > intact crankcase (See #4) > > #7 Later model �squares� came with an updated transmissions, that...
- Re: Overfilling the oil issuesHistorical mailing list - Robert StewartSat, 28 May 2011 03:29:19 -0400...say ... > bring me the van and I'll check it out. > > Crankcase breathing is usually not an issue on waterboxer engines. > I only mention...
- Re: Coolant Loss- is it that time again?Historical mailing list - Dean SWed, 30 Mar 2016 14:17:16 -0400...MacMillan < > stuartmacm@gmail.com> > >>> wrote: > >>> > >>> > Internal leak would be into the crankcase, and you'd know about that! > >>> > Blown internal head gasket ring would...
- Re: Overfilling the oil issuesHistorical mailing list - Robert StewartWed, 25 May 2011 19:36:22 -0400...to drain back down from > the heads and top of the crankcase. > > However if you see oil from between the engine and tranny and...
- Re: Manifold measuring - is this right?Historical mailing list - Michael ElliottThu, 25 Oct 2007 07:42:01 -0700...What happens when you disconnect the crankcase breather hose ? And > when you put your thumb/whatever over/in it? You're the second person...
- Re: ISV questions (updates and clarifications)Historical mailing list - John RodgersWed, 6 Nov 2002 23:48:19 -0600...think it is saying that I have > to first remove the crankcase breather hose. I'll try that and see what > happens. > > Any advice...
- Re: Emissions, Was: AC While CampingHistorical mailing list - Richard DuvernayThu, 10 Jun 2010 13:36:47 -0700...For other than diesel-powered vehicles, the vehicle evaporative system and crankcase ventilation system are tested to reduce any nonexhaust sources of volatile organic...
- Re: On with its head! (Replacing right head on an '87 2.1 l)Historical mailing list - Matt RoberdsSun, 26 Aug 2007 02:50:25 -0500...When I went back over to his house, we checked it, and the #2 cylinder that we thought was actually firmly in the crankcase...
- Re: Question about Mass Air Flow SensorHistorical mailing list - Robert KeezerWed, 26 Jan 2005 10:55:06 -0800...The hot wire or film is heated red hot to burn off impurities that may have built up from air intake or crankcase vapors...
- Re: Noisy Valve liftersHistorical mailing list - JeffWed, 6 Feb 2013 10:37:56 -0800...Not sure if foaming is the problem, or just that the oil in the crankcase gets aerated which results in lower pressure. Dropping the...
- Re: my first cooling system scareHistorical mailing list - Jeffrey LubinSat, 26 Jan 2008 08:03:56 -0500...connects the water pump to the passenger's side of the crankcase. This location drips down onto an exhaust pipe, and is very close...
- Re: Oil Leaks and Leak Down TestHistorical mailing list - G. Matthew BulleyThu, 2 May 2002 20:15:26 -0400...says that the air could clearly be heard coming from the crankcase breather. These strike me as very poor results indicating the engine is...
- Re: Ran out of gas & now won't runHistorical mailing list - Stan WilderMon, 28 Jun 2004 20:38:43 -0500...Run the vehicle for about 300 miles with the Mystery Oil Mix in the crankcase. It is best to get this 300 miles around...
- Re: 80 Westy Engine Fire - Mystery SolvedHistorical mailing list - Stan WilderSun, 11 May 2003 08:20:59 -0700...The circlip was an extra that had sprung from my Tru-Arc pliers during installation and got lost in the crankcase. Solution: Never have...
- Re: Ideas for lifting water into the Westy water tank?Historical mailing list - Michael ElliottSat, 21 Apr 2007 19:07:02 -0700...piece of cr^p which had bolts and nuts in the crankcase and which blew up a few months after I bought it. I...
- Re: The Value Of a Mechanic That Knows the VanagonHistorical mailing list - Scott Daniel - TurbovansFri, 10 Oct 2008 20:16:28 -0700...And the hard running problem was a cracked crankcase > breather > tower, temp fix with duct tape. > Both problems had been looked at by good...
- Re: what clues about engine health can I get...Historical mailing list - Scott Daniel - TurbovansTue, 15 May 2012 19:42:06 -0700...Supposedly pulled from van to make way for >>>>>>> conversion. >>>>>>> >>>>>>> What I can see upon casual observation: >>>>>>> >>>>>>> - oil leak from base of crankcase breather tower...
- Re: Noisy lifters, rockers, at startup, etc (long)Historical mailing list - Tom YoungSun, 8 Aug 2004 17:00:53 -0700...Its still in > the crankcase, and I still have the issue when I start it up, so I am not sure > it did much...
- Re: Oil dilemmaHistorical mailing list - Dennis HaynesFri, 23 Nov 2012 08:20:48 -0500...Also for those of us that use our vans as daily drivers in winter heated garages or using crankcase and coolant heaters is not...
- Idle Stabilizer Valve - Later UPDATE: problem *NOT* solved!Historical mailing list - David McCallumWed, 24 May 2006 09:50:18 -0600...It has a short hose underneath that connects to the crankcase, and a 2-wire connector on the lefthand side. The Idle Control Module...
- pistons shatter 91 wasterboxerHistorical mailing list - Ray HunnamWed, 10 Dec 1997 13:08:40 -0800...Went well for for the warranty period then I started to hear funny noises coming from the crankcase. Also developed a water leak from...
- Re: 85 wbx miss at idle...update =)Historical mailing list - Chuck MathisMon, 19 Jan 2004 06:47:33 -0600...problems....The dipstick had >pulled out about 1/2 inch...losing crankcase pressure. > I stuck back in, and running improved greatly...Also, >after some...
- Re: What Oil to Use on Startup?Historical mailing list - OlRivrRatTue, 30 Jul 2013 00:56:29 -0600...cylinder walls, damaged the head, put chunks of > metal into the crankcase. When torn down - it could be seen it was a > mess. A...
- message for stanHistorical mailing list - Thompson, MichaelTue, 14 May 2002 09:15:37 -0600...Run the vehicle for about 300 miles with the Mystery Oil Mix in the crankcase. It is best to get this 300 miles around...
- Re: New Engine ConversionHistorical mailing list - Jim AkibaFri, 22 Jun 2007 12:36:25 -0400...The zetec uses a cast-iron block, with aluminum head and AL sub-crankcase, but is still lighter than the ecotec. So you get...
- '71 bus; engine in - RUNS!;thanks;introHistorical mailing list - Mitch CovingtonThu, 12 Oct 1995 11:11:58 -0400 (EDT)...It was about 18 degrees off perpindicular to the seam of the crankcase, when it should have been perp. This led to wondering if...
- Re: Warming the oil in cold weather? Other options.Historical mailing list - Rocket J SquirrelMon, 4 Jan 2016 18:21:00 -0800...The vws had a circular thing >>>>> under the centre of the crankcase. They also had a "battery blanket" >>>>> to keep the battery warm. Vanagons...
- Re: Ran out of gas & now won't runHistorical mailing list - Stan WilderMon, 28 Jun 2004 21:34:13 -0500...Run the vehicle for about 300 miles with the > Mystery Oil Mix in the crankcase. It is best to get this 300 miles around...
- Re: Another D15 connector failure example- The fix!Historical mailing list - Alistair BellSat, 19 Feb 2022 21:14:12 -0800...and I’m not thinking d15 had anything to do with fire. > > The d15 supplies ign coil and, this is the kicker, the crankcase...
- Re: Isolating an idle problem?Historical mailing list - Don HansonSun, 21 Dec 2014 19:15:35 -0800...Oil in > the intake track is a sign of excessive piston blow-by or a crankcase > venting problem. > > As for the idle going down...
- Re: Engine BalancingHistorical mailing list - G.M.BulleyThu, 24 Oct 2002 07:31:00 -0400...If you can evaluate the mileage on the engines by crankcase stains, cylinder head stains, carbon deposits on pistons and valves and rod bearing...
- Re: '88 lurching at 2500-3000 rpmHistorical mailing list - Shawn Wright, SMUS Network AnalystMon, 11 Mar 1996 19:57:19 PDT...it eventually > goes to the crankcase breater thing in the middle of the back of the engine > (back is back). somewhere along that hose...
- Re: 82 Diesel oil pressure switch and thermal sensorsHistorical mailing list - Old Volks HomeTue, 9 Jun 2009 16:51:46 -0700...is sligtly tapered for sealing in an aluminum or magnesium alloy crankcase. The thread on the 028/056 switch is slightly longer and straight...
- Re: G-R-I-P-E-S part 5 oil pres woes and more woes and ....Historical mailing list - Steven DenisSat, 10 Feb 2001 08:03:10 EST...visability..and the handling...and..well..) Put SAE 40 in the crankcase like it's supposed to have..keep your eyes on the oil...
- Re: 2.1 Engine idles at 2600 rpm; 2nd computer doesn't fixHistorical mailing list - Tabe JohnsonTue, 18 Apr 2006 00:15:50 -0400...Check the hose from the Crankcase vent on top of the engine over to the AFM. These will rot out on the bottom and...
- Re: Problem, New Rebuilt Engine, Running Rich, What's Wrong?Historical mailing list - Scott Daniel - TurbovansSun, 19 Jul 2009 11:58:32 -0700...I do, if there's a reason to, make sure that crankcase fumes are coming out of it, and going into the hose that...