Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 25+: 60 results shown for Piston.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: Splitty ditties..(f)
    Historical mailing list - Steve Johnson
    Fri, 2 Feb 1996 14:03:44 -0800 (PST)
    So Thom Fitzpatrick says: > And David Eccles thus wrote: > > > > Whose engine was chronically ill > > Its pistons had popped > > Its valves had dropped > > and its...
  • Re: Brake Woes
    Historical mailing list - Hector Zapata
    Mon, 21 Jan 2002 08:51:44 -0800
    ...The caliper piston is not returning all the way, the brake pad was slightly touching the rotor, allowing only the inside pad to wear...
  • Re: AT Seal and Gasket Replacement
    Historical mailing list - Alan Shearer
    Sat, 23 Feb 2002 01:38:15 -0000
    ...I just replaced the pan gasket, the two 2nd gear brake band piston seals, and two brake band cover O-rings. I bought the...
  • Re: GoWesty Auto Parts QSC piston kits
    Historical mailing list - Dave Mcneely
    Thu, 31 Mar 2011 20:53:37 -0500
    ---- Scott Daniel - Turbovans <scottdaniel@turbovans.com> wrote: > for one vendor to say 'we have that same thing for a lower price' .. > I don't...
  • JLP rebuilt wbxr engines in Denver ?
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 6 Feb 2011 19:52:43 -0800
    ...but used pistons with new rings and honed original barrels ( ??...sounds strange to me ) so anyone ...? A customer is suggesting/wondering about this option...
  • Re: reinstalling gas tank
    Historical mailing list - Rob
    Sun, 4 Feb 2007 12:14:40 -0800
    ...I got it! > >Good for O-rings, brake rubber, air tool piston seals, etc Good stuff! Rob becida@comcast.net With a '91 Subaru...
  • 2.0 Liter air cooled rod mod
    Historical mailing list - thomas LaPointe
    Thu, 31 Jul 2008 13:26:06 -0500
    ...it may have been something to enable better oil cooling to the pistons. any ideas? thanks -- 1985 Full Westy "Rustfalia" 1982 Full Westy "dead...
  • Re: Removing head studs
    Historical mailing list - Carroll Smith
    Mon, 23 Nov 1998 15:55:55 GMT
    ...Should I be using an >impact driver, heat or what? Pistons and all are removed, with most >necessary new parts for re-assembly sitting...
  • P&C procedure CAN be done!!
    Historical mailing list - Jay & Kim Schmidt
    Wed, 10 Nov 1999 15:35:29 -0600
    Last week I querried about how to replace cylinders onto pistons when the cylinders insisted on coming off with the heads. Most responses were...
  • Re: Bleeding clutch hydraulic system
    Historical mailing list - Alistair Bell
    Wed, 17 May 2000 08:17:23 -0700
    ...Cleaned 3 small holes in piston. Everything >looks good. > >Only possibile problem I can see, perhaps the forward (in direction of >flow) cup . > >Could...
  • Re: yet another engine choice - VW "twincharger"
    Historical mailing list - Andrew Grebneff
    Fri, 30 Sep 2005 22:38:04 +1200
    ...I never mentioned jets, I said PISTON-engined. >The P-51 D was the fastest prop aircraft then, and is now. >They ate ME...
  • Re: Auto trans - 2nd gear brake band adjusting screw
    Historical mailing list - Scott Daniel - Turbovans
    Thu, 10 Mar 2011 11:24:09 -0800
    ...There is a piston that is behind the big > round cover on the driver's side of the transmission. I am talking > about the...
  • Re: Mark Stephens six-stud system
    Historical mailing list
    Wed, 23 Jun 1999 17:37:28 PDT
    ...larger than 96 mm pistons. > > The 96 mm pistons will work IF you add ceramic coating on the piston top, > combustion chamber, exhaust valve...
  • Re: 83 Vanagon Waterboxer
    Historical mailing list - Benoit
    Sat, 15 Jan 2005 00:11:44 -0500
    ...of course, you said blue oil!!! and westy don't have valves seals so rings / piston must be the problem.....but i wonder, you...
  • Re: Power Brake Bleeding
    Historical mailing list - Rico Sapolich
    Fri, 8 Dec 2000 07:59:09 EST
    ...Are you aware that you should place a block of some sort beneath the brake pedal in order to keep the master cylinder piston...
  • 2.1L crankshaft pulley bolt torque
    Historical mailing list - John
    Tue, 6 Feb 2001 13:01:27 -0500
    ...Tool #3159 - piston wrist pin ridge reamer (Bentley pg. 13.47) Tool #3091 - Piston wrist pin remover (Bentley pg. 13-44/46/47) Tool...
  • Re: 2.1 distributor drive gear installation question
    Historical mailing list - David Kao
    Wed, 13 Aug 2008 14:59:06 -0700
    ...With #1 piston at TDC the distributor rotor will point to an opposite direction rather than the mark on the distributor. Just pull the...
  • Re: Brakes went out
    Historical mailing list - Alan Felder
    Thu, 6 Aug 2009 12:29:30 -0500
    Sounds like MC piston stuck in the compressed position. Alan On Thu, Aug 6, 2009 at 12:20 PM, Rob <becida@comcast.net> wrote...
  • Re: Well oh ya?
    Historical mailing list
    Mon, 24 Jun 1996 12:42:28 -0400
    >What about those Radial >piston engines? Those things amaze me. >Dennis. > > Nah, Dennis, those are only complicated. The miracle occurs when you decide *not...
  • Re: French Syncro Club-Oettinger TD engine
    Historical mailing list
    Thu, 12 Dec 1996 00:45:41 -0500
    ...7 bar? Are there internal changes such as head gasket or pistons? What is the cost for this conversion kit? Thanks for the info
  • Re: why does #3 pist/cyl always go bad first?
    Historical mailing list - EMZ
    Tue, 25 Aug 1998 07:34:57 -0400
    ...Mon, 24 Aug 1998 JordanVw@AOL.COM wrote: > why does #3 piston and cylinder always go bad first on the aircooled type 4 > engines...
  • Re: What's wrong with that picture....
    Historical mailing list - Angus Gordon
    Thu, 21 Oct 2004 11:23:33 -0400
    >Now, my problem is that i cause that bending!!!!!! >The #4 piston rings where almost seized due to a faulty head gasket, coolant >was...
  • Re: rings to 2.1L
    Historical mailing list - BenT Syncro
    Fri, 17 Feb 2006 10:39:05 -0800
    ...the > size of Cilinder is 94.8 m.m and the piston 94.2m.m somebody know where I > can buy Rings over sizes...
  • Re: Big end rod clearance 2.1 WBX
    Historical mailing list - Jeff Ensing
    Sun, 11 Mar 2007 22:45:19 EDT
    ...I usually do pull the rods to check the bearings when I have the pistons out. Jeff E. Atlanta , Ga. 87' Westy "weekender" 91...
  • Re: High Performance Wasseboxers?
    Historical mailing list - EMZ
    Sun, 14 Mar 1999 12:17:51 -0500
    ...The crank is counter weighted and balanced > with the rods and pistons. Seems like a good way to add more power. > Darrell > > Ps. Following...
  • First Timer Overhaul... Some Questions
    Historical mailing list - Chris Gkikas
    Mon, 26 Jun 2000 17:41:11 -0400
    ...I'm looking at an overhaul to find either a busted piston, wrecked rings, thrown rod, all of the above, the sky is falling...
  • Re: Cause of broken valve?
    Historical mailing list - Dennis Haynes
    Sat, 2 Aug 2003 13:40:26 -0400
    ...If the valve broke and the head fell off, you have to hope it put a whole in the piston. If it fell to...
  • Re: Thread locker on rod bolts?
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 22 Aug 2011 19:42:44 -0700
    ...The AAZ uses a shorter rod and a taller piston. the 1Y NA I am building ( balanced too ) will have TD rods and pistons...
  • Re: semi-urgent auto transmission question, update
    Historical mailing list - Edward Maglott
    Mon, 13 Sep 2010 06:40:11 -0400
    ...Edward At 10:58 PM 9/12/2010, Dennis Haynes wrote: >I'm thinking crack or tear in the forward clutch piston. Even new...
  • Re: Timing on rebuilt engine
    Historical mailing list - Stuart MacMillan
    Thu, 20 May 1999 14:24:25 -0700
    ...By hand, of course, slowly turn the pulley until the piston touches the bolt, mark the spot at the case centerline on the pulley...
  • Fwd: Euro-Engine: 87 Volkswagen Vanagon, Mechanical, cylinder head and piston sleeves
    Historical mailing list - Derek Drew
    Mon, 22 Mar 1999 16:42:40 -0500
    ...87 Volkswagen Vanagon, Mechanical, > cylinder head and piston sleeves >To: IATN-EURO2@PEACH.EASE.LSOFT.COM > >iATN Help: send blank email to: help@i...
  • Re: I learned alot about my brakes today....
    Historical mailing list - Stuart MacMillan
    Mon, 30 Jun 2008 20:52:19 -0700
    ...Disk brakes "self adjust" because the rubber piston seal retracts just enough to pull the pads back a fraction of an inch. Springs do...
  • Re: Here goes nothing...
    Historical mailing list - Dennis Haynes
    Mon, 21 Dec 2015 11:03:01 -0500
    ...If the pistons and cylinders are not damaged they could very well be re-used. They don’t normally wear. The usual failures are...
  • Re: How does a leak down tester work???
    Historical mailing list - Don Deitke
    Wed, 26 Jan 2005 12:11:20 EST
    ...I will explain the test very simpily to all . // You want to bring your piston to top dead center of each cylinder to be...
  • Re: Is THIS the "boxer" transplant we've been waiting for?
    Historical mailing list - Raimund Feussner
    Thu, 8 Mar 2018 14:27:21 +0100
    ...So how can you control intake/outtake strokes? You would need to modify the position of the opposing pistons to each other, maybe. That...
  • Re: Compression losses
    Historical mailing list - Blue Eyes
    Tue, 5 Jan 1999 11:24:16 -0600
    ...The compression ratio is the numerical comparison of the volume contained by the cylinder plus the cylinder head when the piston is all the...
  • Re: What's wrong with that picture....
    Historical mailing list - Dennis Haynes
    Fri, 22 Oct 2004 23:49:51 -0400
    ...JIMT is right, the #4 (left) as a bent conecting rods so the piston is lower by 1/4in (it should be equal to...
  • Weird engine meltdown... Attn: Bob MacD and Jake Raby
    Historical mailing list - Jim Arnott
    Wed, 25 Aug 2004 20:39:15 -0700
    ...Type I sorta guy.) Tear down old old motor. (A SIR rebuild with 12k on it.) Find a divot out of the #1 piston...
  • Re: Oettinger flat-six motor and accesories info wanted
    Historical mailing list - BenT Syncro
    Sun, 16 Jan 2005 00:44:20 -0800
    ...I believe they came as 2.8 liter by using WBX 1.9 pistons and barrels; then 3.2 liter using pistons from the...
  • Re: SA big brakes: caliper rebuild kit?? UPDATE!
    Historical mailing list - Tom Sinclair
    Sun, 19 Feb 2006 10:29:08 -0800
    Smallcar also sells a front brake kit using Audi twin piston calipers: http://www.smallcar.com/brakekitft.htm Tom --- John Rodgers <inua@CHARTER.NET...
  • Re: [Fr] little engine alternate moral
    Historical mailing list - Jim Felder
    Fri, 28 Mar 2014 20:45:46 -0500
    Well, it's still Friday, so-- "When the piston of learning meets the dropped valve of experience, the camshaft of respect goes off like...
  • LONG BLOCK vs SHORT BLOCK??
    Historical mailing list
    Thu, 3 Nov 1994 09:59 EDT
    ...alternators...sheet metal and other parts strapped on, while the short block is the core, pistons, and heads and valves...thanks in advance john.
  • Cylinder sleeves
    Historical mailing list
    Sat, 21 Sep 2002 11:20:37 -0600
    ...One went right back in, but the other is past the piston rings. I understand there is a way to put this back together...
  • Re: Engine Overhaul Questions
    Historical mailing list - John Tullier
    Wed, 22 Jan 2003 09:35:22 -0800
    ...I already have a bearing set for the engine, but it contained no bearings for the piston to connecting rods. I'll sort it...
  • Cylinder hone -thanks all
    Historical mailing list - Scott W.
    Fri, 23 Jan 2004 09:05:19 -0800
    ...I think I will go with new barrels and pistons when the money makes itself available, the job is just to big be wasting...
  • Success!
    Historical mailing list - Brendan Slevin
    Thu, 27 Sep 2007 08:42:12 -0700
    ...Then the liners honed, new rings and pistons in them and now they are in the engine! Woo hoo! I am now back to...
  • Re: Engine Replacement or Gasket Fix?
    Historical mailing list - Mike Collum
    Sat, 23 Aug 2008 16:24:59 -0400
    ...I don't think anything is melted. > To melt a thermostat housing the pistons and the cylinder heads > had to be melted first. Seeing...
  • Re: Leak Down Testing
    Historical mailing list - Jerry
    Sun, 31 Dec 2006 12:57:59 -0600
    ...It might make it tough to keep the piston at TDC for a lengthily period. Kind of depends on engine wear and friction. You...
  • Vanagon Specifications Sheet
    Historical mailing list - VW Doka
    Wed, 2 Sep 2009 16:20:52 -0400
    ...002 (.06) Pistons - Diameter 3.700 (93.98) Pistons - Standard Clearance .001-.002 (.02-.05) Pistons - Maximum Clearance .008 (.20) Piston Ring #1 End...
  • Re: off with her heads
    Historical mailing list - Dennis Haynes
    Thu, 28 Nov 2013 10:49:01 -0500
    ...And I'm sure I'll my > sanity will thank me when I put the piston rings on (without removing the pistons). > > If you...
  • Re: EV piston slap - how noticeable?
    Historical mailing list - Jeff DeLeeuw
    Wed, 05 Feb 1997 00:08:04 -0800
    ...that've been described in this list as symptomatic >of EV piston slap. > >My previous two cars were both VW diesels, a rabbit and...
  • Re: Sticky brakes
    Historical mailing list - Scott - IMAP
    Tue, 28 Jun 2016 13:03:42 -0700
    ...One advantage to the later style single piston calipers is that having only one caliper piston somewhat reduces the ability of the pads and...
  • Re: Strange Auto Trans Behavior
    Historical mailing list - BenT Syncro
    Mon, 24 May 2010 04:10:54 -0700
    ...The typical culprits after a repair are the > accumulator seal, or one of the piston seals, or a broken ring on > the direct > drum...
  • Vacuum Brake Booster
    Historical mailing list - Helen Fahy
    Fri, 23 Aug 2002 09:17:05 -0400
    ...The piston material is aluminum and is very scored on the bottom perimeter of the forward piston. It almost looks like this unit has...
  • Re: What's wrong with my VW? Friday
    Historical mailing list - Andrew Grebneff
    Mon, 3 Mar 2003 18:09:32 +1300
    > >>Shame the kit wasn't the best quality, and it had a piston which was >perforated... eventually burned badly > >Never heard of a perforated...
  • Re: 2.1 Wasserboxer
    Historical mailing list - Bob Donalds
    Fri, 12 Jan 2007 11:11:53 -0500
    ...As far as the pistons I can offer you german piston or Cofap nobody has ever told me they felt any differance in performance...
  • Re: Draggin caliper, bad bearing job, or paranoia?
    Historical mailing list - Scott Daniel - Shazam
    Sat, 21 Jun 2008 19:04:26 -0700
    ...the two piston early calipers commonly have a stuck piston. you push the pistons back, or just squeaze on the edge of a pad...
  • Re: GEX Vanagon Engines
    Historical mailing list - Dennis Haynes
    Fri, 20 Mar 2015 22:54:52 -0400
    ...Call, ask what you are getting, what upgrades are available such as new heads and a better piston-cylinder set or even rings. New...
  • Re: Leak-down Test - How to??
    Historical mailing list - Michael
    Sun, 23 Mar 2014 15:04:44 -0400
    ...You can add a squirt of oil in the spark plug hole and move the piston back and forth to improve the leaky cylinder...
  • Re: stumped
    Historical mailing list - Scott Daniel - Turbovans
    Fri, 18 Dec 2009 18:57:26 -0800
    re "TDC was > determined with a dial indicator on the top of the piston. " yes, but on WHICH tdc ? - the piston comes up on...