Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 21+: 60 results shown for Piston.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: Brake work pictures
    Historical mailing list - Scott Daniel - Turbovans
    Fri, 24 Jul 2009 18:21:48 -0700
    ...on the two piston early type ...........I find a lot of outer pistons kinda stuck, or solidly stuck. Usually worse on the right side...
  • Re: Jaguar vs. Passat brakes on Vanagon
    Historical mailing list - OlRivrRat
    Sat, 4 Feb 2012 14:03:08 -0700
    ...This is calculated by the radius squared x pi. >> A 3" piston has an area of 28.274 cu in. Two 1.5" piston...
  • Re: Borrow ring compressor in SW Ohio area?
    Historical mailing list - Ken Wilford
    Wed, 2 Mar 2011 10:53:00 -0500
    ...Be sure you hone the cylinders with plenty of oil and bathe the pistons with oil when you install the rings. I like to...
  • Re: ENGINE FAILURE-could be caused by too lean air-fuel mixture
    Historical mailing list - Dennis Haynes
    Wed, 13 Mar 2002 07:55:39 -0500
    ...A lean mixture can cause warped-burned valves and melted pistons. So will over-advancing the ignition timing. Over the years, I've have...
  • Re: I4 Happenings in turbovans land
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 27 Jun 2011 11:43:43 -0700
    ...The block is of a 1.8L but the Crank, piston rod, and piston exchange provide the displacement to increase to 2.0L. The...
  • Re: Cylinder Heads!
    Historical mailing list - Kenneth Madsen
    Mon, 18 Mar 2002 14:51:57 -0500
    ...Then it needs to slide down the piston as you push the cylinder over the rings one by one. After all 3 rings on...
  • Re: Tools for engine overhaul on 85 waterboxer
    Historical mailing list - Mark Seifert
    Tue, 20 Apr 2004 21:52:58 -0700
    ...I need the specialized tools that are required to >remove/replace pistons and sleeves and any other specialized tools >(removing circlips and piston pins...
  • Re: Case and pistons shot?
    Historical mailing list - Tom Young
    Mon, 7 Feb 2000 17:25:45 -0800
    ...Case and pistons shot? > re: The cases/cranks used in the air-cooled Vanagons are all the same > whether carburated or FI. > > Does the...
  • Re: failure to fire: the sequel
    Historical mailing list - Roger Sisler
    Tue, 12 Sep 2006 20:08:35 -0400
    ...Remove the solinoid and clean the piston and cylinder with 800or 1000grit sand paper. Grease the piston and cylinder.Use RTV when reinstalling the...
  • Re: diagnosis--blown piston ring?
    Historical mailing list - dylan friedman
    Fri, 27 Mar 2009 14:15:21 -0700
    With all the engine conversions going on, I have been picking up the wbxers for for around $400 cash. Many post to come and...
  • Re: 2200cc liners
    Historical mailing list - BenT Syncro
    Wed, 12 Sep 2007 17:05:07 -0700
    ...Most retailers can get you the pistons and cylinders. BenT
  • Re: Heads stuck to piston sleeve
    Historical mailing list - richard
    Wed, 8 Jul 1998 10:51:46 -0500
    put oil in cylinders,replace spark plugs you now have a hydraulic press to press the heads off, or a small diameter coil of...
  • Re: Removing head studs
    Historical mailing list - Karl Mullendore
    Mon, 23 Nov 1998 09:08:08 -0500
    ...Of course,you'll need to remove the cylinders and pistons for this! Have fun! Karl
  • Re: increasing displacement/compression on 1970cc engine
    Historical mailing list - Kent Christensen
    Sun, 23 Jan 2000 21:01:25 -0700
    ...is there any way to increase the power without swapping engines when I do this rebuild? maybe some performance parts (cylinders, pistons or something...
  • new parts for sale
    Historical mailing list - dawn
    Sat, 31 Mar 2001 23:19:41 -0800
    ...95 got these parts before my vanagon blew the lifter and piston going with i-4 conversion now donot need parts anyone want them...
  • Re: Adventure Wagon Vs. Westy
    Historical mailing list - Thompson, Michael
    Wed, 24 Apr 2002 13:23:39 -0600
    Dear All A simple question How easy or otherwise is it to change a piston and cylinder, rings etc on an aircooled Vanagon with...
  • Re: found new pistons and cylinders for cheap
    Historical mailing list - Simon Reinhardt
    Mon, 31 May 2004 19:24:22 -0600
    FWIW, Ken Morgan @ Euro Cars (remember him?) tried the chinese P&C's at first, but found that they weren't even consistently round...
  • Re: Death Valley
    Historical mailing list - Geza Polony
    Tue, 23 Jan 2007 15:22:38 -0500
    ...How are you going to replace a piston at 8,000 ft in the mountains in the middle of nowhere? I mean, there's...
  • Re: GEX Vanagon Engines-where to get a good engine
    Historical mailing list - Stuart MacMillan
    Sat, 21 Mar 2015 10:21:14 -0700
    ...http://www.gowesty.com/ec_view_details.php?id=24110&category_id=82&category_ parent_id= Custom forged pistons, AMC heads with better valves...
  • Re: Flushing brakes ATE calipers rebuilding
    Historical mailing list - Paul Guzyk
    Wed, 3 Jan 2007 21:38:54 -0800
    ...Then bleed the upper valve like one piston calipers. If your caliper seals are grungy, you may want to remove them and clean/rebuilt...
  • Re: 2.1 distributor drive gear installation question
    Historical mailing list - Jim Felder
    Wed, 13 Aug 2008 17:07:31 -0500
    ...IMO, the Bentley should read "insert the drive gear so that with the #1 piston TDC, the rotor points to the mark on the...
  • Re: New-Spark-Plugcebo Effect
    Historical mailing list - Dennis Haynes
    Tue, 21 Aug 2012 20:49:11 -0400
    ...New-Spark-Plugcebo Effect "Let the piston meltdowns and broken rings begin." Even I, a registered Vanagon ninnyhammer, would not want to melt my...
  • Florida lemons
    Historical mailing list
    24 Aug 94 14:29:08 GMT
    ...After hearing of the "piston slap" problem common to EV's from James Lindley (formerly of Penn State , now somewhere in Alaska), I asked...
  • Re: Alternative way of reinstalling cylinder liner
    Historical mailing list - Doug in CA
    Tue, 30 Mar 2004 13:41:58 -0800
    Why not pull the piston off and put it back in the cylinder first? ----- Original Message ----- From: "Mike Collum" <collum@VERIZON.NET> To: <vanagon...
  • Re: &^%(^&%&^%$b wrist pin clips!
    Historical mailing list - Frank Condelli
    Sat, 14 May 2005 06:21:40 EDT
    ...What's the secret to getting these things in and out (the circular wire clips that secure the wrist pins in the piston)? Any...
  • Re: 1.9l Home Rebuild?
    Historical mailing list - Zoran Mladen
    Wed, 16 Feb 2000 11:10:57 -0500
    ...There are some difficult times, such as removing pistons and installing cylinders, but all in all a fairly simple process. The other important thing...
  • Re: Auto trans kit? Parts Source!
    Historical mailing list - Dennis Haynes
    Thu, 29 Nov 2012 11:41:50 -0500
    ...65030 Bushing Kit 65070 front seal 65076A Axle seals A65010A Filter A65964 Forward Clutch Piston A65022 2nd gear brake band A65962A Reverse Clutch Piston...
  • Re: Leaking Caliper
    Historical mailing list
    Thu, 6 Apr 95 13:46:05 MST
    --David Schwarze said:-- > > > > Just found that the right inboard brake piston is leaking > > around the boot. I just rebuilt these a couple of months...
  • fridge air pumps
    Historical mailing list - Dan Houg
    Thu, 25 Jul 1996 15:29:21 CST6CDT
    ...that knob on the air pump threads onto a rod that operates the piston for the air pump. the rod attaches to the piston...
  • '86 Westfalia front brakes
    Historical mailing list - Ray Tubbs
    Tue, 20 Oct 1998 20:54:26 EDT
    Attempting to replace front pads but the piston in the caliper won't budge. Decided to open the bleeder valve to reduce the pressure...
  • TECH TRICK- install cylinders without removing the motor
    Historical mailing list - Smola, Tony
    Thu, 14 Mar 2002 18:59:22 -0600
    ...I read this somewhere on the internet, where this guy took a regular ring compressor band and nylon tied it around the piston and...
  • Re: [Syncro] Re: Resend -Question about SA brake kits
    Historical mailing list - Bill Davidson
    Sun, 3 Mar 2002 08:19:10 -0800
    > The pistons o nthe SA big brakes are slightly larger than those on any other > T3/ Vanagon/Syncro out there. The larger rotor provides...
  • Re: piston pin #1 removal question
    Historical mailing list - George Goff
    Sat, 10 Jan 2004 18:45:48 EST
    In a message dated 1/10/04 4:56:42 PM, collum@VERIZON.NET writes: << After removal, clean the varnish off the wrist pin...
  • Re: engine break in oil?
    Historical mailing list - ROBERT DONALDS
    Sun, 15 Aug 2004 12:15:32 -0400
    ...When I assemble any engine air or water cooled I increase the piston skirt to cylinder clearance from the stock new measurement of .0015ths...
  • Re: Audi 2.3 l conversion report (long)
    Historical mailing list - Bruce J. Wilbur
    Wed, 18 Aug 1999 22:41:38 -0700
    ...The valves impacted the pistons and bent the stems. The pistons >were fine, only had to be polished. The cylinder walls looked brand new...
  • Re: Engine Timing
    Historical mailing list - Mark Ingalls
    Sun, 18 Mar 2001 22:39:05 -0600
    ...I have NEVER EVER heard that this is a safe thing >to do. > >You will risk detonation (the fuel ignites while the piston is...
  • Re: Sticking front calipers
    Historical mailing list - Shawn Wright
    Mon, 2 Apr 2007 08:04:16 -0700
    On 1 Apr 2007 at 17:17, Dennis Haynes <d23haynes57@HOTMAIL.COM> wrote: > I have never seen a piston fall out of a caliper...
  • Re: What is pinging? (Was Re: 73 bus / timing question...)
    Historical mailing list
    Thu, 27 Jun 1996 09:34:34 -0500
    ...As the piston is moving up the cylinder the exploding air/fuel tries to push it back down. The pinging (rattling) results, and is...
  • TDC ?
    Historical mailing list - Christopher M. Smith
    Tue, 28 Jan 1997 11:27:41 -0800 (PST)
    ...I've always understood TDC as position at which the #1 piston is at the top of the cyclinder (viewable with a light down...
  • Re: 82 diesel cooling problem cont'd
    Historical mailing list - Martin Jagersand
    Mon, 12 Jul 1999 16:32:26 -0400
    ...1/ Inside piston of the brake calipers often start sticking before outside. Flex in the rotor makes it looks as if the brakes still...
  • Re: Rear disks in a Vanagon
    Historical mailing list - Ben T
    Mon, 29 Oct 2001 01:39:09 EST
    ...South African Big Brake kit? Are you using single piston calipers? Are the pistons any bigger than the SA kit? How about the rotors...
  • Re: Opinions Please
    Historical mailing list - Benny boy
    Sun, 21 Jan 2007 16:00:00 -0500
    ...It's the head or a piston/ring of course, so money will have to be invested anyway (i have good 2.1 used...
  • Re: Is this the cause of my engine compression problem?
    Historical mailing list - Dennis Haynes
    Sun, 17 Jun 2007 16:55:42 -0400
    ...More than outer diameter, ring land wear is the main driver in regular replacement of pistons during rebuilds. There could also be other causes...
  • Re: New engine, was Re: Ecu fix addendum
    Historical mailing list - Neil N
    Wed, 1 Apr 2020 16:46:54 -0700
    ...Was test thorough? - I replaced all bearings, rings, pistons so seems a shame I didn't rebuild the head too. My '81 and '88...
  • Re: Ping in 1.9 Wasser Boxer
    Historical mailing list - Dennis Haynes
    Mon, 7 May 2001 06:49:27 -0400
    Are you sure you are hearing "ping"? It may be the sound of a loose piston, pin bushing, etc. Ping will usually get worse...
  • Re: need new engine for air-cooled van (overheated one)
    Historical mailing list - Dennis Haynes
    Wed, 5 Jul 2006 11:01:50 -0400
    That piston meltdown had nothing to do with driving over 45 mph during break in. This was ignition timing or maybe mixture related. The...
  • Re: Knock Knock ?
    Historical mailing list - Scott Daniel - Shazam
    Fri, 14 Dec 2007 16:30:15 -0800
    ...Piston slap would more likely be due to a piston installed backward or a size tolerance problem between the cylinder and piston. A bad...
  • Re: *Sigh* Leaky Wheel Cylinder (PICS)
    Historical mailing list - neil N
    Sat, 5 Sep 2009 09:56:43 -0700
    ...Then > when the piston does move the leaks begin. > > Also depending on brake shoe material you may be ready for brakes anyway. > > Dennis I...
  • Re: Junk yard find.
    Historical mailing list - Robert A. Alexander
    Wed, 13 Jan 1999 23:18:11 -0500
    ...I'm looking for something that I can replace a piston in for about the same amount of bucks I spend at Pizza Hut...
  • [FIX]auto tranny experts HELP!(little long)
    Historical mailing list - Dan Noll
    Sat, 8 Jun 2002 13:56:53 -0400
    ...This all started when I tried to fix my 2nd gear brake leak. (I posted before and got no response)I destroyed the piston...
  • Re: The value of instrumentation
    Historical mailing list - dbeierl
    Sat, 27 Oct 2018 13:39:37 -0400
    ...only mechanism the lifter has to accommodate decreased clearances in the system (oil leaking through the clearance between lifter wall and piston). Yrs, d
  • AVP Engines
    Historical mailing list - Chris Dixon
    Tue, 26 Jul 2005 00:13:08 EDT
    ...I'd have had a better motor if I'd kept in my clattering previous motor with busted #3 valves and a slapping piston...
  • Re: engine swap (ignorant questions) -> EV piston slap
    Historical mailing list - "L-Soft list server at Vanagon List (1.8c)"
    Thu, 11 Dec 1997 15:52:41 -0800
    ...Try HELP. >> >> >> I don't believe "Piston Slap" is HYPE, as it was claimed. I have a >> >> > Unknown command - "I". Try HELP. >> Unknown command...
  • wisdom of brake fluid res. location
    Historical mailing list - Scott Daniel Foss - Turbovans
    Wed, 4 Feb 2004 14:52:28 -0800
    ...when you've done a few of those..and fluid is coming out when you push the piston down.then you can mount it...
  • Re: will 1.9L to 2.1L parts swap
    Historical mailing list - Evan Mac Donald
    Sun, 27 May 2007 08:19:09 -0700
    ...The piston cylinders are the same. The bore for both engines is 94mm. Most of the differences lie in the reciprocating assemblies. The crank...
  • Re: Miscellaneous Aircooler Questions
    Historical mailing list - Vanagon Man
    Sat, 18 Aug 2001 16:08:42 -0400
    ...I'm planning to use a set of OEM Koblenschmidt 914 2.0L pistons for a bit more power, and if I have to...
  • Re: Engine Rebuild Questions
    Historical mailing list - Jake de Villiers
    Tue, 7 Apr 2009 12:02:47 -0700
    ...sleeves, pistons, camshaft etc... >> >> I am awaiting a final parts list from him now but want to be sure I am >> not missing anything...
  • Re: [T2] A cc'ing the heads question-answered
    Historical mailing list - Tom Young
    Mon, 3 Mar 2003 20:02:54 -0800
    ...However, if you're using an AMC head then the method you describe will give you the "real" deck height (top of piston to...
  • Re: need advice re: rebuilding 84 Vanagon engine
    Historical mailing list - Scott Maurer
    Mon, 16 Dec 1996 17:31:45 +0000
    ...Am I right? I removed the rods from the crankshaft with pistons attached and pounded out the piston pins with a "wood dowel rod...
  • Re: 2.1 hydraulic lifter rebuild kit available?
    Historical mailing list - David Beierl
    Fri, 26 Oct 2012 09:58:34 -0400
    ...The piston is fitted to the bore with a ridiculously small but carefully controlled clearance. I wouldn't be at all surprised if pistons...