Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 20+: 60 results shown for Idle Stabilizer.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Engine Miss
    Historical mailing list - Peter Pollard
    Sun, 21 Dec 2003 02:26:09 -0500
    ...checked idle stailizer valve and unit ( electricals). Adjusted CO content by voltage of the O2 Sensor. Cleaned Idle stabilizer valve. Tune up to correct...
  • Re: need some ID on parts
    Historical mailing list - Dennis Haynes
    Wed, 28 May 2003 22:23:00 -0400
    ...Assuming 1.9l with Digijet, the box is the idle speed stabilizer. There are 2 versions, one green one black. They activate at different...
  • Re: 91 Westy, low idle stall, low power ....help! (LENGTHY REPLY)
    Historical mailing list - Mike Frost
    Thu, 21 Jul 2005 22:09:42 -0700
    ...The RPM cable going bad will cause the idle stabilizer valve to stop working properly which would cause the symptom you are describing. The...
  • Re: Idle Stabilizer Control Relay_Schematic_Parts List?
    Historical mailing list - Neil N
    Fri, 16 Oct 2015 16:07:22 -0700
    ...com> wrote: > Does anyone have a schematic/parts list for the Idle Control Module/relay > in the later Digifant systems? > > Looks like there is...
  • Re: oxygen sensor and alternator lights
    Historical mailing list - kenneth d lewis
    Tue, 22 Feb 2000 22:23:47 EST
    ...Try flushing out your idle stabilizer valve and lubricating. Do not use silicone. Check for vacuum leaks. What does it idle at when warmed...
  • Re: Idling....
    Historical mailing list - - James Shinosky
    Thu, 6 Aug 1998 01:04:58 EDT
    ...the new one is tiny 100ohms higher than the old one) I also sprayed the idle stabilizer valve with carb cleaner. RESULT: 2000rpm cold...
  • Engines,Ecus and more FS!!
    Historical mailing list - KW
    Tue, 10 Oct 2000 10:06:14 -0700
    ...w housing $125.00 2) complete Engine harness' $300.00 2) Idle Stabilizer control units $100.00 Each E-mail me if you want...
  • Re: 91 Carat Cold Stall
    Historical mailing list - John Rodgers
    Tue, 15 Oct 2002 11:35:17 -0500
    Lew, the first place to start tracking down this problem is to check your idle speed with the Idle Stabilizer Valve (ISV) disconnected. Be...
  • Re: Engine warm-up troubles
    Historical mailing list - Mark Dorm
    Sat, 26 Aug 2000 21:28:04 PDT
    ...This analog signal tells the idle stabilizer valve to open the >correct amount to produce smooth idle. The idle speed relay is located in...
  • Re: '87 Vacuum plumbing question
    Historical mailing list - Bill Collins
    Mon, 10 Nov 2008 15:06:09 -0500
    ...intrex.net> wrote: >> On my '87, the short hose between the idle stabilizer valve and the air >> chamber below it has a molded fitting...
  • Re: unplugged idle stab valve
    Historical mailing list - S_J_ WACKER
    Thu, 30 Jul 1998 20:15:40 -0700
    Dan, I have been running my 86 Syncro with the idle stabilizer control unit out for about six months. The valve is still in...
  • Idle test for digifant.
    Historical mailing list
    Thu, 8 May 1997 12:45:17 -0500 (CDT)
    ...Next you will need to check the idle stabilizer. Refer to Bentley page 24.53 1. With the ignition on the stabilizer valve should...
  • First no lights or wipers but WOULD start - now WON'Tstart
    Historical mailing list - allan harris
    Tue, 28 Oct 2003 15:48:29 -0800
    ...Both idle stabilizer and fuel pump were silent. Hell then it started up again. Pushing accelerator has NO effect on process. Hmmm... Allan Harris...
  • Great info: Vanagon head leaks and Fuel injection problems
    Historical mailing list - Brent Christensen
    Tue, 16 Apr 2002 17:44:43 -0700
    ...The Idle Control or Stabilizer Valve was disconnected, the engine would idle at 800 and die often when cold. Once warmed up it would...
  • Re: WTB: bad Idle Control Unit
    Historical mailing list - John Rodgers
    Fri, 29 Apr 2005 16:35:01 -0500
    jbange wrote: > Looking for a couple BROKEN idle control modules for a reverse > engineering > project. Investigating the feasibility of replacing it with a simple...
  • Re: Intermittent running problem.
    Historical mailing list - OlRivrRat
    Thu, 28 Apr 2016 14:37:02 -0600
    ...symptoms of a failed idle stabilizer control unit: >> >> http://www.van-cafe.com/home/van/page_434_755/idle-stabilizer-control-unit-r >> ebuilt...
  • Re: Moral qestion--Now diagnostics
    Historical mailing list - Benny boy
    Sat, 20 Jan 2007 09:52:19 -0500
    ...7.5* BTDC and have set the idle using the dashboard tach with the idle stabilizer disconnected. Soon as I have time, though, I...
  • Re: What's a Hall sender do?
    Historical mailing list - David Beierl
    Mon, 8 Apr 2013 18:54:08 -0400
    ...Also on the Digifant system idle stabilization is accomplished by a much fancier system that operates a tiny auxiliary throttle (the Idle Stabilizer Valve...
  • more fi concerns
    Historical mailing list - Jason Willenbrock
    Sun, 4 Feb 2001 18:24:03 -0500
    ...could it be idle stabilizer? running too lean? too rich? o2 sensor? temp 2 sensor? fi injectors? i am going crazy here. i imagine...
  • Re: Bride of RapidIdle
    Historical mailing list
    Tue, 6 Feb 2001 08:05:18 EST
    This is actually called the ISCU (Idle Stabilizer Control Unit) and it is located behind the right rear tail light in 86-91 Vans...
  • Re: hall effect sender output characteristics?
    Historical mailing list - David Beierl
    Tue, 21 Oct 2003 16:30:36 -0400
    ...Duration around 10 ms at idle, proportionately less at speed. Leading edge corresponds to each spark initiation except when the idle stabilizer is messing...
  • Re: Intermittent running problem.
    Historical mailing list - Dennis Jowell
    Fri, 29 Apr 2016 15:55:29 -0400
    ...I checked the idle stabilizer control unit sprayed all the contacts and cleaned them. No change,so that seems good. New fuel filter also...
  • Re: Starting issue - low idle and wants to stall
    Historical mailing list - Dennis Haynes
    Tue, 5 Jul 2011 00:45:16 -0400
    ...It is also possible that you have an engine or injector issue that the idle stabilizer cannot compensate for. Dennis -----Original Message----- From: Vanagon...
  • Re: Low Idle w/A/C on 91 Westy
    Historical mailing list - kenneth d lewis
    Thu, 30 Jul 1998 10:05:34 EDT
    Mark; I believe the idle stabilizer should compensate for the extra load. You also might to take a A/C line pressure reading. A...
  • Idle Stabilization Valve
    Historical mailing list - Sylvie et Germain
    Tue, 15 Apr 2003 22:57:29 -0400
    ...The idle is very rough and I need to keep the throttle slightly open during the warming up. I suspect the Idle Stabilizer Control...
  • The Mouse that ate our Vanagon
    Historical mailing list - L&A Johnson
    Fri, 7 May 1999 09:01:55 -0400
    ...The little bu**ers had eaten through 8 of the 11 wires connecting the Idle Stabilizer Relay and 5 of the eaten wires were...
  • Re: Parts Wanted
    Historical mailing list - Chris Donaldson
    Thu, 28 Mar 2002 22:22:09 -0600
    ...Grey Rear hatch Insert in Grey Digifant Idle Control Unit (behind passenger tail light) Idle Stabilizer Valve Tail pipe and gasket Westfalia single mudflap...
  • Re: 84 ign timing spec
    Historical mailing list - Old Volks Home
    Wed, 5 Sep 2007 10:13:38 -0700
    ...http://www.oldvolkshome.com/ignition.htm#V8384 And yes, vacuum is connected, but be sure to temporarily disconnect and bypass the Idle Stabilizer so...
  • Re: Rough running till warmed up
    Historical mailing list - David Kao
    Mon, 20 Aug 2007 22:15:08 -0700
    ...Plugging > >> them > >> together bypasses the idle stabilizer so it won't fight idle > >> adjustments > >> made via the big screw in the throttle body. > >> > >> Don...
  • Re: Idle Stabliser Control Unit
    Historical mailing list - Stuart MacMillan
    Tue, 4 Jan 2000 12:22:47 -0800
    ...Am I likely to do any harm by leaving the wires permanently bridged > and the Idle Stabilizer right out of the ignition circuit? (I...
  • Re: Recall for Fuel tank
    Historical mailing list - EMZ
    Wed, 2 Jun 1999 22:22:17 -0400
    ...still a open recall on > > the gas tank, sending unit, and idle stabilizer on the '87 Syncro Camper! > > G, I wish those were valid...
  • A few part for sale
    Historical mailing list - Joe in NH
    Sun, 29 Feb 2004 11:12:49 EST
    ...idle stabilizer box, $45 7. radiator fan motor and fan, $60 Actual shipping costs only. Thanks, Joe in NH
  • Re: Miss at idle?
    Historical mailing list - Dennis Haynes
    Fri, 13 May 2016 17:05:21 -0400
    ...of what I haven't done: > > Hall Sensor.. > Coil.. > Fuel Injectors.. > Idle Stabilizer Module.. > > I know that I need to adjust the throttle body...
  • Rough Idle troubleshooting need
    Historical mailing list - Steven Mills
    Fri, 11 Sep 2015 15:37:24 +0000
    ...So far, have tested with good parts ECM, AFM, Dist, plugs, plug wires, alternator, coil, fuel pressure/flow rate, idle stabilizer, cold temp sensor...
  • Re: '87 Oil pressure NEED HELP!!
    Historical mailing list - Shawn Wright
    Wed, 24 Jul 1996 07:58:33 PDT
    ...Thanks!!!!!! Idle specs for 87 are: 880 +/-50 rpm, with everything off (ie: a/c) Although if idle stabilizer is working, it should keep...
  • 1985 FAST idle
    Historical mailing list - Ignace Speybrouck
    Mon, 26 Nov 2001 22:16:05 -0500
    ...No difference in idle with idle stabilizer in or out Complete new and tight exhaust system New O2 sensor All visible engine compartment ground...
  • digitool readings help needed
    Historical mailing list - Vanagon man
    Wed, 12 Jun 2002 12:43:27 -0400
    ...get a plume of black smoke............the idle stabilizer IS functioning, vacuum is 15in at idle, and the fuel pressure reg is within spec...
  • Replace FI with carb??
    Historical mailing list - bill
    Sat, 12 Apr 1997 13:20:21 -0700
    ...I am told this eliminates the conputer, injectors, air flow meter, idle stabilizer, and a few other parts. I am thinking of doing this...
  • Parts FS
    Historical mailing list - Gary McEachern
    Tue, 10 Sep 2002 19:49:43 -0400
    ...The harness is complete in nice condition, with all connectors (none of the connectors have been cut). $75.00 Idle stabilizer from 1990 2WD...
  • Re: Idle Stabilizer Control Unit Reverse Engineering
    Historical mailing list - TC
    Tue, 9 Jan 2007 14:12:57 -0800
    > 1) Figure out a good replacement (or permanent repair/upgrade) for the > AFM. I have made some real good progress on this, and will...
  • Re: FW: Idle Control Issues
    Historical mailing list - JRodgers
    Sat, 20 Jul 2013 12:24:59 -0500
    ...have stabilizer issues. John On 7/20/2013 10:23 AM, John Meeks wrote: > FWIW, when I was having a runaway idle issue I...
  • Re: 87GL, Cold Engine Problem
    Historical mailing list - Brad Snyder
    Tue, 6 Jun 2000 12:46:04 -0400
    ...My van will run OK with the idle stabilizer unplugged, but the idle is a little slower. On Mon, 5 Jun 2000 14:00...
  • Re: Intermittent running problem.
    Historical mailing list - Jim Felder
    Thu, 28 Apr 2016 16:58:33 +0000
    ...Jim On Thu, Apr 28, 2016 at 11:32 AM Stuart MacMillan <stuartmacm@gmail.com> wrote: > Classic symptoms of a failed idle stabilizer control...
  • Re: Cold Start Injector doesn't turn off.
    Historical mailing list - Dr. John H. Lauterbach
    Tue, 16 Mar 1999 22:36:53 -0500
    ...Are you sure >you aren't looking at the AIC (auxillary idle control) valve? It's >also called the idle stabilizer in vw parlance...
  • Fw: 1986GL update
    Historical mailing list - Dave Baker
    Sun, 6 May 2001 15:06:20 -0500
    ...key and it runs. > With Idle stabilizer disconnected it runs at 1200 RPM till it dies. > With stabilizer connected it runs at 3000 RPM...
  • VW Quantum Question/ No Van Content
    Historical mailing list - Pat Dooley
    Thu, 1 Apr 1999 22:14:10 -0500
    ...A short hose that runs from the intake to the idle air stabilizer collapses under manifold vacuum. The motor makes an audible sucking noise...
  • Re: Idle Stabilizer Control Unit Reverse Engineering
    Historical mailing list - jon
    Mon, 8 Jan 2007 11:42:46 -0800
    > never seen a burnt out newer ICU. Now, I've tried replacing that BD438 > transistor and have had no luck. Maybe there are other...
  • Re: Hesitation while driving (manual)
    Historical mailing list - Pat Spragge/RFAN
    Fri, 16 Oct 2015 14:10:29 -0700
    Does it do it regardless of the engine temp? Does your Idle Stabilizer Valve work? Did you check the timing? Pat From: Steven Johnson...
  • Re: idle problems
    Historical mailing list - Lawrence Johnson
    Fri, 3 Dec 1999 09:51:55 -0500
    ...the Idle Stabilizer Relay. The ISR is located behind the right rear tail light and is a black box about 3"x3"x1". -Larry...
  • Re: problem 86 camper weekender
    Historical mailing list - Aristotle Sagan
    Wed, 20 Mar 2002 12:51:40 -0800
    ...Compression is good , timing and idle at >specs. tempsensor2 checks out although it is difficult to get a >reading. Replaced the idle stabilizer valve...
  • Re: Fwd: 1985 Vanagon - Replacing Engine
    Historical mailing list - David Beierl
    Mon, 28 Feb 2000 16:45:59 -0500
    ...You should also have a small green (or black) rectangular box, the idle stabilizer, mounted on the left side between the ignition coil and...
  • Re: Idle issues...
    Historical mailing list - Doug Noganav
    Thu, 2 Apr 2009 15:09:05 -0800
    You might want to check the idle stabilizer relay behind the right tail lamp. Mine was acting up recently and I cleaned the contacts...
  • Off idle Syndrome
    Historical mailing list - Terry Kay
    Sun, 5 Nov 2000 15:14:41 -0600
    ...I've replaced the OX sensor,idle stabilizer, and the Temp II sensor, and the darn thing doesn't want to come off idle...
  • Re: Throttle Valve Switch
    Historical mailing list - Jay L Snyder
    Wed, 28 Aug 2002 15:58:45 -0400
    ...I suspect that your irregular idle is a function of a failing/failed idle stabilizer. Jim > > Date: Wed, 28 Aug 2002 11:34:19...
  • Re: Aftermarket Air Conditioning
    Historical mailing list - Blake Heinlein
    Sat, 30 Dec 2006 00:12:37 -0500
    ...My main problem will be the mounting bracket and the idle stabilizer. Thanks, Blake On 12/29/06, JordanVw@aol.com <JordanVw@aol.com...
  • Re: emission failure, HC 229 @ idle (ok @ 2500 rpm)
    Historical mailing list - ROBERT DONALDS
    Thu, 26 Aug 2004 20:56:22 -0400
    ...over-advanced and set the idle speed to 950-1,000 rpm. > Yes this is above the idle stabilizer attempted 800-850. The extra...
  • Re: a/c and idle
    Historical mailing list - Jake de Villiers
    Mon, 30 Jan 2006 19:05:00 -0800
    ...Shawn > >> > >> > >> > >> > > > > Sounds like it's worKing just right to me. > > > > The idle stabilizer increases rpm under the following conditions to > > prevent engine stalling: > > > > A...
  • Re: 1985 Vanagon GL
    Historical mailing list - John Lauterbach
    Sat, 19 Aug 2006 22:41:44 -0400
    ...I have yet to see a bad idle stabilizer keep engine from starting. If engine has good compression, then it is worth some time...
  • Re: Anything like this for 1.9L?
    Historical mailing list - David Beierl
    Sat, 28 May 2011 21:08:38 -0400
    ...For example -- the little >electronic idle stabilizer box on the left side of the engine. I know >what it does for a living, but...
  • Re: timing tyro
    Historical mailing list - Coby Smolens
    Sun, 28 Nov 1999 19:40:14 -0800
    ...Disconnect and plug together wiring harness ends at idle stabilizer on left side of engine compartment. 5. Adjust idle speed to 875 rpm. 6...