

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 19+: 60 results shown for Rotor.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Overland Big Brakes-SyncroHistorical mailing list - Bob StevensSat, 22 Apr 2006 16:29:25 -0600...I "added" two (2) washers as spacers of about 3mm, between the carrier and caliper, which center the rotor in the caliper. Two washers...
- Performanc brake pads? (long)Historical mailing list - Don HansonSun, 30 Mar 2008 08:02:22 -0800...It was equipped with Brembos from a Twin Turbo 911, with hollow and perforated brake rotors with four pistons in each caliper. The so...
- Re: Problem removing grease cap from front wheel???Historical mailing list - neil NSat, 15 Aug 2009 11:57:21 -0700...With new rotors, my P-side grease cap would slide off when installed on the new rotor. (new smooth surface, greasy, good seal, slight...
- Re: '87 Syncro brake failure?Historical mailing listTue, 30 Jul 1996 20:08:33 -0400...What happened? >> You got the pads and rotors so hot that they lost thier grip. This can be fairly dangerous as this type of...
- 5400rpm rev limiting rotors for 10 bucks at cipHistorical mailing list - Courtney HookSat, 29 Oct 2011 15:30:51 -0700So does anyone actually use one of these, or are they like me and have a tach on the dash? If you do use...
- Re: WankelsHistorical mailing list - Robert A. AlexanderThu, 15 Oct 1998 20:50:52 -0400...8000rpm & 326ft.lb./7500rpm- OR one of the '91 LeMans 4-rotor normally aspirated 26Bs - 700HP/9000rpm & 448ft.lb./6500rpm. Which would you suggest...
- Re: [Syncro] Re: Resend -Question about SA brake kitsHistorical mailing list - Ben TMon, 4 Mar 2002 21:25:28 EST...The rotors are to big to fit inside a 14" wheel. BenT
- swap of front end components?Historical mailing list - Derrek WittmmannFri, 11 Oct 2002 15:31:12 -0700...8 gas and I would like to upgrade it to power steering and cast lower control arm plus thicker brake rotors. thanks Derrek Wittmann
- Re: OX and charge lights onHistorical mailing list - George GoffTue, 21 Jan 2003 15:25:33 EST...alt is going bad >> Loosen the fan belt then check the rotor for runout (aka, slop). Also, pull the brushes to measure their lengths...
- Re: Differences in SA Big Brake KitHistorical mailing list - mark drillockFri, 10 Jan 2003 16:03:05 -0800In essence what Sean said is that the SA big brake kit converts 2wd Vanagons to use the same front rotors as Syncros. Mark...
- Re: Vanagon Brake Pads - Bendix TitaniuMetallic iiHistorical mailing list - wognaciousSun, 3 Jun 2007 08:51:14 -0700...This coating raises the brake pad's initial stopping power while the pad mates to the rotor surface. After about 50 stops the TitaniuMetallic...
- re: brakes on EVHistorical mailing list - robert barwise, LKG2-2, 508-486-5367Wed, 1 Nov 95 11:44:25 PST...My EV rotors are not vented, btw. I'd be interested in a write-up on the procedure when you're done. BTW, what...
- Re: Drilled Rotors vs. Big Brake Kit - related QHistorical mailing list - Damon CampbellWed, 6 Nov 2002 09:04:18 -0800...to improve braking, but if the big brake kit (or vented rotors) isn't the way to do it, what is? -Damon David Brodbeck...
- Re: '84 1.9: 3/4 power and running uglyHistorical mailing list - Benny boyWed, 25 Aug 2004 14:45:48 -0400Not the plug, not the rotor not the O2 (Safe mode) not anything related to normal maintenance.... This is so incredible that mechanics try...
- Re: Rough Running 1.9LHistorical mailing list - Alan HosageThu, 7 Oct 2004 07:04:32 EDT...He had already replaced the cap, rotor, plugs, fuel filter, tried a differnt pump, temp II sensor, and O2 sensor. I checked for any...
- Re: Eccentric hub?Historical mailing list - SDF ( Scott Daniel Foss )Mon, 28 Apr 2014 12:47:52 -1000...usual suspects are out of round drum'/s, rotors with excessive runnout or varying thickness , and those sorts of 'brake' things.' but also .. a...
- Re: Power Steering Pumps - Again!Historical mailing list - Shawn WrightMon, 23 Aug 2010 15:38:03 -0700...A few gaskets and seals, a spring loaded >> pressure relief valve, a stator, a rotor, and some vanes to go in the >> rotor. >> >> The...
- Re: Hydraulic valve lifters?Historical mailing list - Scott Daniel - TurbovansSat, 22 Aug 2009 13:47:18 -0700...cap lying on the side (so I could see the rotor while I was turning > the engine). I think I fried the cap and...
- RE: VANAGON digest 1087Historical mailing list - Stephen BiblerMon, 2 Sep 1996 09:22:35 -0400...This time I found the generic distributor rotor had melted near = the outer contact. Changed the rotor out with a Bosch replacement and = things...
- Re: Audi rotors instead of SA discs?Historical mailing list - Chris S.Thu, 18 Sep 2014 12:38:10 -0400...8:53 Chris S <szpejankowski@gmail.com> napisał(a): > Sometimes manufacturers post their rotor dimension on the internets. I found a reference to an...
- Re: Never brag (and please help get my van started...)Historical mailing list - AaronMon, 9 Apr 2012 06:42:00 -0700...On Apr 9, 2012, at 6:18 AM, "Chris S." <szpejankowski@gmail.com> wrote: > I world look at regular maintenance items first like rotor...
- Re: DISTRIBUTOR, INSTALLINGHistorical mailing list - Fred YoungerMon, 15 Feb 1999 12:33:49 -0600...Both talk about "aligning the rotor with the notch in the distributor > body that corresponds to the number cylinder." I can't figure to...
- Re: Brake service questionsHistorical mailing list - Karl WolzThu, 27 Jul 2000 13:48:53 -0700...what point is it necesary to > replace the rotors and drums? > > 2) When replacing the rotors and/or drums, go with new or or...
- Re: VolkscafeHistorical mailing list - Terry K.Wed, 24 Apr 2002 13:58:35 -0500I bought a new set of rotor's, pads and bearings, on Sunday--- I was notified with a tracking number on Monday morning, and...
- Re: syncro speedo cableHistorical mailing list - Anders LundinMon, 15 Sep 2003 08:04:43 +0200...i pulled off the front rotors, unturnable, bummer. anyways, i was looking for the speedo cable. on my 90gl the cable runs thru the...
- Re: AAA info request..Historical mailing list - J Greenberg G Jannini10 Apr 96 21:51:15 EDT...We replaced the fried distributor cap & rotor, cleaned the plugs, and were on our way. Having the tools isn't always enough. George '89...
- 2.1L maintenance @120kHistorical mailing list - Richard C WelshFri, 1 Oct 1999 14:33:49 -0400have put 20K on an '87 GL since purchase 3/98 from orig owner. (No maintenance records) besides basic plugs/wires/cap/rotor/filters...
- Re: Fuel tank removal disappointmentHistorical mailing list - Bill CollinsFri, 5 Sep 2003 04:38:47 -0400...Fuel pressure is good (at least normally, could not induce symptoms > while testing), new plug wires, cap, rotor, plugs ok, timing ok, hall > sender...
- Brake upgradesHistorical mailing list - Cullen StewartTue, 12 Aug 2008 17:29:51 -0400...Is their a brake pad that is truly superior? Should I have the rotors drilled?
- Re: New brakes, now pulls to the leftHistorical mailing list - Jake de VilliersSun, 2 Aug 2009 19:27:14 -0700...The rotors are warped or maybe the drums. On Sun, Aug 2, 2009 at 7:16 PM, Trooz <trooz@roadrunner.com> wrote: > I took...
- Re: Points Glazed hard starting 81Historical mailing list - Stan WilderFri, 16 Nov 2001 15:37:03 -0600I found the problem" It was a bad rotor. This was, as always in combination with other things like oily points, a dirty connection...
- Re: OEM vs Aftermarket -- WAS: where is the best buy for drums and rotors?Historical mailing list - Jim FelderThu, 17 Feb 2005 17:45:17 -0600...where is the best buy for drums and > rotors? > > Funny thing about some of the aftermarket parts: if you look closely, > you > see where...
- THANKS - Report (brakes)Historical mailing list - neilMon, 16 Apr 2007 12:19:55 -0700...Fronts have even wear and pads/rotors hardly worn at all. I'm taking it in to have a power bleed done and rear...
- Re: Drilled Rotors vs. Big Brake Kit - related QHistorical mailing list - Larry ChaseWed, 6 Nov 2002 08:20:53 -0700...Drilled Rotors vs. Big Brake Kit - related Q A little while ago, i switched to 15" wheels as well, hoping to fit larger, more...
- Why Bigger Brakes Was Cause of brake rotor warpingHistorical mailing list - Mike MillerFri, 13 Sep 2013 11:28:45 -0700...When the holes cracked and connected in > these rotors it was time to put on a new set. Breaking in new pads was > important...
- Re: [sagp2002] Re: SA Big Brake Kit QuestionsHistorical mailing list - Ian XTue, 28 Jan 2003 10:20:54 -0800Has anyone done a cross reference of part numbers for the pads, calipers, or rotors for local parts store equalivalents? I just got my...
- Re: How to spend $500 dealer credit in 40 days?Historical mailing list - pckingSun, 19 Mar 2017 14:48:35 -0400...master cylinder, clutch slave and master, > brake slaves rear, front rotors, calipers. These all go bad after 100 k > miles and eventually need replaced...
- Lube Points on New Front Brakes?Historical mailing list - neil NTue, 7 Apr 2009 09:04:46 -0700...Installed new calipers, rotors, pads. Caliper hardware kits c/w a little tube of grease which I assumed was only for the back of...
- Re: Poor idleHistorical mailing listMon, 08 May 95 11:20:13 PDT...Thinking it might be the basics I changed the spark plugs, cap and rotor. They needed changing but it did not fix the problem...
- Gas Milage problem(?)Historical mailing list11 Mar 96 21:49:00 +1800...cap, and rotor? Wires, plugs,points were replace before Thanksgiving trip to Disney(for those who remember), don't know when the dist cap...
- re Eurovan brake vibrationHistorical mailing list - Rick Sherrod (hopeless VW nut)Wed, 15 Oct 1997 10:22:50 -0500...My original >Goodyear tires have 20k miles, cann't see any uneven wear. >VW replaced the front brake rotors; this didn't change anything...
- Re: Pulsing Brake PedalHistorical mailing list - Karl WolzSat, 20 Apr 2002 17:08:43 -0700...Pulsing Brake Pedal > If you're feeling it while braking from speed, it likely is warped front > rotors. They may be 'turned', or trued...
- Re: Squeaking Wheels When Brakes Not AppliedHistorical mailing list - Russell PattenFri, 9 Jul 2004 11:51:36 -0500...The pads have worn to fit the rotors. :) Seems like such an easy DIY maintanance item to ignore..... -Russell >Volks, > >Last week, I replaced...
- FS: 84 Vanagon GL (Guelph, Ontario, Canada)Historical mailing list - VeedubWed, 4 Apr 2007 00:46:38 -0400...Water pump Front brakes - pads, rotors, bearings Rear brakes - backing plates, wheel cylinders, pads New master cylinder Replace some of the hard brake lines...
- Need Bosch parts sourceHistorical mailing list - Dan HougMon, 13 Feb 1995 15:04:48 CST6CDT...a good supplier for Bosch parts? Ideally, a Bosch rebuilt starter but also need the 'little stuff' ie plugs, cap, rotor etc. tia -dan
- Re: Wet weather bluesHistorical mailing listMon, 26 Apr 1999 16:29:58 EDT...Cap Rotor Spark Plug Wires Spark Plugs lately? Look inside your cap. You will probably see a nice set of black trails from one...
- Re: Rev Limiter? - 1.9LHistorical mailing list - Rico SapolichWed, 22 Nov 2000 12:10:12 EST...9L of which I have knowledge is in the form of a centrifugal switch built into the distributor rotor specified for this engine. Rich
- Re: [Syncro] Re: Resend -Question about SA brake kitsHistorical mailing list - Bill DavidsonSun, 3 Mar 2002 08:19:10 -0800...The larger rotor provides a better heatsink and > the axial venting provides better cooling. So can these 15" SA brakes be used in stock...
- Re: Front brake noise of 91 WestyHistorical mailing list - Ben TSun, 8 Sep 2002 19:12:29 EDT...are driving while under the eliminated influence with alcohol? ;) >> See Bob? The alcohol on my rotors already got my grammar all influenced & benT. BenT
- Stalling solved (knock on wood)Historical mailing list - Debbie WaltersFri, 4 Apr 2003 20:23:49 -0500...I had replaced the cap, rotor and Hall sender, without any luck. Just replaced the entire distributor, and that did the trick. deb '85...
- Re: '86 up brake improvent on vanagon??Historical mailing list - Chris SWed, 9 Jul 2003 07:03:40 -0400...front brake parts that were changed from 85: > 1. caliper > 2. rotors > 3. brake hoses > 4. steering knuckle > > Mark The '86 and-up parts...
- Brake pedal is high in warm weather?Historical mailing list - BajaLeoThu, 13 May 2004 17:12:37 -0700...I bled the brake system a while back while replacing front rotors. Any Ideas
- Re: Go Westy Big Brake kitHistorical mailing list - BenThu, 12 Sep 2013 14:25:42 -0700...Unfortunately, as with > many SA parts, supply is spotty and are backordered. > I have a sneaking suspicion the rotors are not of high quality...
- Re: Brake pedal pumping.Historical mailing list - Larry AlofsThu, 15 Mar 2001 18:42:52 -0600...Replaced one caliper and > one rotor, and bled system. Only replaced the one rotor that was at minimum > spec, the other was fine. Used...
- Re: Squealing BrakesHistorical mailing list - Terry KayTue, 2 Oct 2001 07:23:02 -0500...This translates to HARD!!! This also translates to new rotors due to the abrasiveness if the "new" ceramic materials. Better to use old fashioned...
- Re: steering feedbackHistorical mailing list - Robert FisherSun, 26 Sep 2004 07:25:31 -0700...The suspension, alignment and linkages checked out, so he replaced both rotors and pad sets and generally 'cleaned up', but that's all he...
- Re: 84 Vanagon missing throughout driving range?Historical mailing list - Matthew PollardFri, 19 Apr 2002 17:23:58 -0700...Is the cap seated on the distributor correctly? Is the rotor seated firmly down on the distributor? Check vac-lines. When you mess with...
- Replacing Brake Rotors, calipers, bearings.Historical mailing list - R. E. HauflerWed, 11 Aug 2004 19:44:06 -0400...Can someone explain the proper procedure for installing the rotor/bearings? (Torque, then dent, must a new nut be used each time). I drive...
- Re: Knockin soundHistorical mailing list - jimtMon, 25 Oct 2004 13:30:42 -0600...I recently had two new front rotors installed > and the bearings looked fine at the time (about 2 months ago) Any > insight? > > > Dave > > > > > David...
- Re: K&N, from K&N...Historical mailing list - Mark FitzsimonsTue, 9 Jan 2001 17:14:43 EST...Apache helicopters used in Desert Storm and the US Marine Corps new Osprey tilt-rotor aircraft. >> The Osprey? Now there's an endorsement!! : ) mark