Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 18+: 60 results shown for Input shaft.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: diesel to gas conversion ongoing...
    Historical mailing list - Don Hundt
    Fri, 3 May 2002 21:35:39 -0700
    ...Took a little off of the diesel tranny input shaft with my dremel - > hopefully enough. > > Tomorrow we'll stick it in, hook up the...
  • Re: 1985 Vanagon - front steering column "u-joint"
    Historical mailing list - Mike Collum
    Fri, 2 Nov 2007 10:39:33 -0400
    Jim, The standard steering uses the flat rubber joint at the steering box input shaft. Power steering racks require a true U-Joint which...
  • Re: R&R Transmission with winch?
    Historical mailing list - Chris S
    Sat, 9 Jan 2010 20:41:54 -0500
    ...Jack up rear wheel, jack > stand, remove wheel, drag tranny out. > > Or would this setup not allow input shaft to clear things? (angle > introduced...
  • Vanagon Diesel Parts and Motor FS $800
    Historical mailing list
    Mon, 23 Aug 1999 09:54:39 EDT
    ...I will include the bellhousing and input shaft you need to convert your waterboxer tranny over to use it in the conversion. The engine...
  • Steering rack do it yourself rebuilding?
    Historical mailing list - jbclem1
    Sun, 24 Jul 2005 17:09:24 -0700
    ...Rack end bushings Pinion adjustment bushing Input shaft bearing Grease seal The end bushings have to be honed to fit right, and you use...
  • Re: why "constant" velocity joints?
    Historical mailing list - Evan Mac Donald
    Mon, 16 Jul 2007 17:37:03 -0700
    ...Standard rear-wheel drive drive shafts have the yokes offset at 90 degrees to each other, so as one yoke tries to go faster...
  • Re: Installing Starter Bushing
    Historical mailing list - Mike
    Sat, 13 Sep 2008 22:06:22 -0400
    ...It not too likely, but it could end up in the flywheel engine or trans input shaft seal, causing a leak. You'd have...
  • Re: Slow turnover when starting.
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 15 Apr 2012 01:18:08 -0700
    ...in neutral to > eliminate the pilot bushing hanging up on tranny input shaft dragging it > down!! > > Velma 82diesel 1.6 na westy > > On Apr...
  • Re: What parts could I use?
    Historical mailing list - Al and Sue Brase
    Thu, 28 Oct 2004 23:02:51 -0500
    ...cradle with attaching hardware > pan and oil pickup > bell housing > transmission input shaft > flywheel & clutch > starter motor > exhaust system and manifold > > Jim > On Thursday...
  • Re: Neil Wigley's transaxle noise
    Historical mailing list - Todd Hill
    Thu, 21 Jan 1999 14:16:36 EST
    ...The input shaft is not supported by bearings but by the coupler with the mainshaft. The rear caged needle bearings on the mainshaft rarely...
  • My Trans problem fixed! :-)
    Historical mailing list - Shawn Wright
    Sat, 19 Jun 1999 08:13:36 -0700
    ...Total cost came to $1100 CDN, including a used input shaft to replace mine which was chewed up by three failed pilot bearings. It...
  • Re: pilot bearing was- Clutch - revisited - Shim question
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 20 Jun 2010 14:52:17 -0700
    ...I have never had one not come right out of a waterboxer crankshaft. 'transmission input shaft seal' I think was meant, not output ..that...
  • Re: 1972 (engine almost in?!?!?) Westfalia
    Historical mailing list - David Schwarze
    Tue, 11 Jul 1995 21:02:40 -0700 (PDT)
    ...Like you say, you have to move the engine back to clear the input shaft, and things hit the rear of the engine compartment...
  • Re: What's this syncro westfalia worth?
    Historical mailing list - 80 Westy Pokey
    Fri, 29 Nov 2002 15:16:28 -0500
    ...Syncro Westfalia For Sale > >One unfortunate thing is the missing drive shaft... I took it out a couple >years ago to avoid wear and...
  • Re: Almost ready to pull 2.1--questions
    Historical mailing list - The Westy man
    Sat, 21 Jun 2008 09:50:37 -0700
    ...looks like it's gonna be tight) as it clears the input shaft and then >>lowers. > > > -- > No virus found in this incoming message. > Checked...
  • Re: Westy Diesels
    Historical mailing list - Martin Jagersand
    Fri, 10 Sep 2004 09:19:15 -0600
    ...our a adaptor plate and coupler from the flywheel to the input shaft and the right torque converer that would be compatible with a...
  • Re: diesel tranny needed
    Historical mailing list - ROBERT DONALDS
    Fri, 20 Aug 2004 13:08:58 -0400
    ...can sell you the Diesel tranny > minus the bellhousing and the input shaft. Of course, since I don't > have the aircooled tranny yet...
  • Re: Pilot bearing failure
    Historical mailing list - Dennis Haynes
    Sun, 16 Aug 2015 10:18:49 -0400
    ...When the flywheel goes on it will collapse > > the > outer > > shell and the input shaft will not be able to spin free or it...
  • Re: flywheel pilot bearing will not fit!
    Historical mailing list - John Philcox
    Fri, 14 Nov 2003 10:07:21 -0500
    ...end of the pilot bearing > making it impossible to install the input > shaft of the transmission, without major > force. This is exactly what the...
  • Re: CV-Joints question
    Historical mailing list - Dana Morphew
    Tue, 8 Dec 1998 16:22:40 -0800
    ...coupling shaft will accelerate and > decelerate many times per second as it goes flexing down the road, but the > input and output shaft will...
  • Re: CV Joints
    Historical mailing list - Dennis Haynes
    Sun, 27 Apr 2014 09:58:05 -0400
    ...At $100/hour labor just installing 2 boots costs more than a rebuilt or economy shaft assembly. However CV joints usually do not suddenly...
  • Re: Sound conundrum - input requested
    Historical mailing list - Richard Koerner
    Tue, 19 Oct 2021 22:53:21 +0000
    ...I could reproduce the heavy knocking sound by moving >>> the shaft by hand under the van. I believe the sound is the end of...
  • Re: No gears
    Historical mailing list - cesar quiros
    Mon, 14 Jun 2010 10:17:49 -0700
    ...plate coming > apart so the splined center just spins on the input shaft. > > > BenT > > Sent from my mobile device > > On Jun 13, 2010, at...
  • Re: I need help on my conversion.
    Historical mailing list - Shawn Wright
    Sun, 1 Jun 2003 21:57:13 -0700
    ...I received my freshly rebuilt waterboxer > > trans (from Daryl at AA Transaxle)with diesel bellhousing and input shaft and > > proceeded to install. I did...
  • Re: Easiest Platform to Convert to I-4 FROM?
    Historical mailing list - David Brodbeck
    Tue, 27 Apr 2004 19:02:48 -0400
    ...The input shaft needs to be shortened in the latter case, I'm not sure if this is also true with the adapter plate...
  • Re: Trans upshift
    Historical mailing list - Scott Daniel - Turbovans
    Tue, 10 May 2011 18:41:38 -0700
    ...There are three inputs we can say .. throttle input, governor shaft speed, and what gear is selected. it's a mechanical computer sort of...
  • Re: Transmission Woes
    Historical mailing list - craig cowan
    Sun, 6 Nov 2011 22:25:42 -0500
    ...left of the > pilot brg rollers. > The warning to presever the input shaft by not continuing to drive still > stands. > > I've made one...
  • Re: Oil leak
    Historical mailing list - Tom C
    Mon, 1 Aug 2022 14:42:30 -0400
    ...do the job with it and a pipe > slipped over the input shaft. This was on a waterboxer which I assume you > have. > > Jim...
  • Re: Transaxle Trouble 3rd & 4th - Away from Home
    Historical mailing list - Bob Stevens
    Sat, 23 May 2009 14:56:33 -0600
    ...the tranny > and I am not able to get the plunger shaft to move back and forth for the > 3rd and 4th gear positions...
  • Re: Tranny leak??
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 6 Jul 2009 14:57:57 -0700
    ...the trans input shaft oil seal is pretty straightforward. In the case of really good leaks though ..........I'm always concerned that it's...
  • Re: Clutch diagnosis/opinions please!
    Historical mailing list - Carrington, Tom
    Fri, 28 Jan 2000 14:27:22 -0500
    Yeah, I was wondering of the possibility of the pilot bearing seizing up on the input shaft. A few times with the clutch on...
  • Re: Clutch diagnosis/opinions please!
    Historical mailing list - Carrington, Tom
    Sat, 5 Feb 2000 12:34:53 -0800
    Yeah, I was wondering of the possibility of the pilot bearing seizing up on the input shaft. A few times with the clutch on...
  • Re: GETTING STARTED
    Historical mailing list - David Beierl
    Fri, 15 Jun 2001 12:41:24 -0400
    ...It will create a suction on the input line to pull fuel in if gravity flow isn't sufficient, but it doesn't depend...
  • Re: Growling into reverse
    Historical mailing list - Dennis Haynes
    Tue, 3 Jun 2003 21:50:08 -0400
    ...On any manual transmission car, it is a good practice to depress the clutch, put in a forward gear to stop the input shaft...
  • Re: Engine Is In!
    Historical mailing list - neil N
    Mon, 10 Mar 2008 22:32:34 -0700
    ...11:10 PM, neil N wrote: > > > Images of mounted engine and input shaft stuff in no particular order: > > > > http://tubaneil.googlepages.com/enginein%28sortlater...
  • Re: Lower Engine Stud Needed
    Historical mailing list - Dennis Haynes
    Tue, 17 Jun 2008 11:53:16 -0400
    ...I have see a number of lower studs fail and that can make a mess of the clutch hub and tranny input shaft. Dennis...
  • Re: Play at Manual Steering Rack and Bushings ok? (VIDEO)
    Historical mailing list - Tom Hargrave
    Sat, 17 Jan 2009 23:10:36 -0600
    ...But the play he shows is the result of turning the input shaft back and forth by hand & it's not the bushings compressing...
  • Re: Flywheel Sleeve - WBX 2.1L
    Historical mailing list - Scott Daniel - Turbovans
    Tue, 31 Mar 2009 12:24:47 -0700
    ...The transmission > input shaft goes through this whole assembly of flywheel, sleeve, felt > washer and into the needle bearing in the end of the...
  • Re: 090 (automatic) transmission questions
    Historical mailing list - Larry Alofs
    Sun, 22 May 2016 07:37:57 -0400
    ...also a thrust washer between the reverse plate and the > >> differential input shaft. You have to do some measuring to choose the > >> correct thickness...
  • Re: WTB used Vanagon diesel starter
    Historical mailing list - Roger Whittaker
    Thu, 10 Jun 2010 12:11:59 -0700
    ...and ran that transmission shaft off a timing chain that had a timing chain gear mounted on both the input of the tranny and...
  • Re: Standard to automatic?
    Historical mailing list - pdooley
    Sat, 7 Nov 2009 21:15:47 -0500
    Third gear just couples the input to the output shaft, so the ratio is 1:1. Accounting for the 3 percent slip as Dennis...
  • Re: 1977 VW van hybrid
    Historical mailing list - Daryl Christensen
    Thu, 9 Dec 2010 13:13:56 -0800
    ...or decoupled and drive the front end thru the motors armature shaft. A pile of batteries and maybe an extra generator to recharge what...
  • New Starter Stopped Working requires the RI wizard
    Historical mailing list - gary hradek
    Wed, 11 Sep 2002 09:22:06 -0700
    ...If we can get some input from our wizard in RI I think he can better explain the actual voltage needed. Should check your...
  • Re: diesel gas conversion - fourth day
    Historical mailing list - David Marshall
    Sun, 5 May 2002 21:19:42 -0700
    ...When we last left our heros, they had taken a little bit off the input shaft and were getting ready to put the gas...
  • Re: Not able to engage any gear
    Historical mailing list - Scott Daniel - Turbovans
    Wed, 1 Jun 2011 15:35:20 -0700
    ...it's a press fit into the center hole of the flywheel, and the input shaft will fit through it without touching it. scott...
  • Re: How To Install Your New VC
    Historical mailing list - Steve Schwenk
    Thu, 5 Jul 2001 15:40:21 -0700
    ...Take this > > spacing collar, grease the top rim of it and again > > place it on the input > > shaft in the housing and slightly press...
  • Re: Shift but no go - Update - CV bolts go wheeeeeeeeee!
    Historical mailing list - Stuart MacMillan
    Sat, 28 Oct 2017 09:05:41 -0700
    ...or an axle, the clutch disc center hub, and the input to main shaft coupling. Since you are getting knocking I would look at...
  • Re: R&R Transmission with winch?
    Historical mailing list - Scott Daniel - Turbovans
    Sat, 9 Jan 2010 18:29:05 -0800
    ...No excessive play at input shaft. But. Shifting DK and AB by hand on bench, AB seems to shift harder and noisier. DK smoother...
  • Re: Friday - couple of recent tool acquisitions.
    Historical mailing list - T Collins
    Fri, 4 Sep 2015 12:48:10 -0400
    ...It doesn't have > the input shaft that would allow it to be coupled to the power feed of the > milling machine table ( if...
  • Re: [TDI-conversion] I gotta tranny... what is the gearing? no codes
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 22 Dec 2008 16:59:05 -0800
    ...mark a spot on the input shaft so you can count how many turns it makes. rotate both output ( axle ) flanges equally one full...
  • Re: Engine removal
    Historical mailing list - Mark Mages
    Mon, 18 Mar 2002 20:35:09 -0800
    ...It will basicly slide off the > input shaft of the > >transmission. Lower engine and pull out on floor > jack. > >Sounds easy, is easy. > > > >Follow...
  • Re: Mechanical Geniuses please note! (NVC)
    Historical mailing list - John Rodgers
    Sun, 7 Aug 2005 12:06:30 -0500
    ...The motor - by way of pulleys - > will drive a shaft whose rotational speed should have a controllable > range from 0 to 200 RPM. > > I...
  • Re: 45k out of a tranny?
    Historical mailing list - Dennis Haynes
    Tue, 25 Jun 2013 16:25:15 -0400
    ...of beetles and 25 or 36 HP engines such as the input shaft. The best bet may be to let the last shop that...
  • swishing tranny sounds when coasting in 3rd and 4th - DIY fix?
    Historical mailing list - Will Taygan
    Wed, 4 Nov 2009 09:26:58 -0900
    ...Funny, the input shaft(?) seal was still good. Of course the oil slinger was rattling around. Had the local machine shop secure the oil...
  • Re: Flywheel seal
    Historical mailing list - Stan Wilder
    Wed, 25 Feb 2004 21:49:24 -0600
    ...a standard, I would also replace the seal on the tranny input shaft. It is inexpensive and just as easy to replace as the...
  • Re: No cold start and the shaft from the shop (long)
    Historical mailing list - Jay L Snyder
    Fri, 17 Jan 2003 07:51:41 -0500
    ...No cold start and the shaft from the shop (long) My Boston bob 1.9l engine is having some starting issues. No cold start...
  • FW: [vanagon] Syncro diesel parts
    Historical mailing list - Stuart MacMillan
    Tue, 4 Feb 2014 14:07:06 -0800
    ...Bellhousing, input shaft, diesel fuel tank, starter, oil pan, aluminum engine mounts, carrier bars and a hose set that I bought from quality german...
  • Re: No gears
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 13 Jun 2010 14:24:24 -0700
    ...the axle would just spin in the drum on one side, giving 'no gears' ...as though say, the input shaft to the trans was...
  • Re: CV joint raceway opinion
    Historical mailing list - Robert Keezer
    Sat, 28 Feb 2015 21:19:56 +0000
    ...up this half-shaft again for a while, I'm buying new joints. Thanks for all the insight and input. -Dick Wong- 78 Scirocco...
  • Re: Aircooled transmission into water cooled van- AUTOMATIC
    Historical mailing list - Dave Yates
    Tue, 12 Aug 2008 14:46:18 +1000
    ...The shaft on the 2nd gear band piston of the "aircoooled" is held in the piston by a circlip. This circlip can break, not...