Skip to main content
vanagon.com
SearchSavedAccount
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 17+: 60 results shown for Piston.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: Sticking brakes
    Historical mailing list - Tom Brunson
    Sat, 27 Sep 1997 15:23:57 UT
    ...If it feels like the piston is dragging when you press it in you should pull the calipers, remove the pistons and clean and...
  • 2.1: Check rods or just top end?
    Historical mailing list - tabe johnson
    Tue, 25 Oct 2005 12:58:40 -0400
    ...If I pull the cylinders, what is the accepted way of getting the pistons back in them? Or should I just leave well enough...
  • Re: Measuring fuel pressure
    Historical mailing list - T.M.
    Fri, 31 Aug 2007 18:49:21 -0400
    ...The other two are of the spring-loaded piston-cylinder type, not safe for fuel because the seal relies on the sealing of a...
  • Re: Mobil1 15-50 and setting a new piston ring
    Historical mailing list - OlRivrRat
    Sun, 8 Sep 2013 22:51:36 -0600
    On 8 Sep , 2013, at 6:57 PM, Scott Daniel wrote: > at least change to a conventional, and I'd saythicker oil. Scott Thicker...
  • Re: Vanagon Head Leaking Around The Head Nut(S)
    Historical mailing list - Mike B
    Tue, 15 Apr 2014 04:16:54 -0400
    ...Remove intake and exhaust, pull the heads, > pull the jugs/cylinders and pistons and you are halfway there. New > jugs/cylinders, pistons/rings and...
  • Re: semi-urgent auto transmission question, update
    Historical mailing list - Dennis Haynes
    Mon, 13 Sep 2010 23:54:56 -0400
    Rolling freely goes back to bad piston or other internal leak. Dennis -----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On...
  • Re: total seal ring end gap on 95mm pistons?
    Historical mailing list - Damon Campbell
    Sun, 3 Aug 2003 21:53:45 -0700
    ...Regarding your chevvy comment - to go 101.4mm pistons, you'd have to do some major modification to the case as the cylinders are...
  • Re: 6 mils of lash...
    Historical mailing list - David Beierl
    Mon, 31 Jan 2000 20:53:48 -0500
    ...If you now try to push the piston down again, it acts roughly like a solid bar; the oil trapped under the piston prevents...
  • Re: cheap shipping company
    Historical mailing list - Joachim Preiss
    Sat, 22 Mar 2003 10:54:24 -0500
    ...However, the flywheel and > the pistons > >and sleeves are still in. I plan to split the case. What > should I do > >next? Should I...
  • Re: Is THIS the "boxer" transplant we've been waiting for?
    Historical mailing list - Alistair Bell
    Wed, 7 Mar 2018 18:24:32 -0800
    ...2 cycle Diesel engine, same piston orientation. Ab > On Mar 7, 2018, at 2:42 PM, Roy Nicholl <RNicholl@NBNet.nb.ca> wrote: > > Alistair...
  • How bad is a scored cylinder wall? -I4
    Historical mailing list - Jeff Kennedy
    Wed, 27 Jul 2005 12:42:59 -0700
    ...Can I get away with just replacing the one piston/rings? Will a hone help things? I will be replacing the valves on that...
  • Re: Head gasket questions
    Historical mailing list - Dave Bayer
    Sat, 25 Jul 1998 20:15:51 -0700
    ...First, with the piston you are working on at TDC, pull the >| > cylinder out like you are going to remove the wrist pin. >| >| Did...
  • Re: &^%(^&%&^%$b wrist pin clips!
    Historical mailing list - Robert Fisher
    Sat, 14 May 2005 19:32:20 -0700
    ...The 3/8 > nut is big enough not to go through piston pin but small enough not > to get caught up on the other...
  • Re: Knock Knock ?
    Historical mailing list - Dennis Haynes
    Fri, 14 Dec 2007 18:27:24 -0500
    A tick tick sound under load could be something as simple as and exhaust gasket leak or more complicated as piston slap or even...
  • Re: engine swap (ignorant questions) -> EV piston slap
    Historical mailing list - John Simick 1-800-736-3550
    Thu, 11 Dec 1997 19:17:13 -0500
    ...Try HELP. > > >> I don't believe "Piston Slap" is HYPE, as it was claimed. I have a > > > Unknown command - "I". Try HELP. > Unknown command...
  • Re: Need Automatic Transmission
    Historical mailing list - jbange
    Mon, 2 May 2005 10:10:39 -0700
    ...all the way out,remove the valve >body,install the piston pinand piston,install the adj screw pin and screw, >and then the valve...
  • Re: Febi Diesel Vanagon Oil Pump Quality?
    Historical mailing list - Ralph Meyermann
    Fri, 12 Aug 2016 18:52:38 -0500
    Ahh, I believe the turbo Diesel's have the squirters for the extra fuel/heat load to help cool the pistons. My 1.6na...
  • Re: 2L 914 into '81 Westy
    Historical mailing list - S2
    Thu, 8 Apr 1999 14:18:14 -0500
    When my 82 engine was rebuilt by Ellison Brothers' in 92 they told me they used the european 914 pistons for a bit more...
  • Serious question
    Historical mailing list - developtrust
    Fri, 25 Jan 2002 15:29:14 -0800
    Why is it usually that #3 piston that goes? William P. > About five years ago I blew #3 piston trying to abate a tailgater...
  • Re: Engine Wear
    Historical mailing list - Ben T
    Tue, 19 Feb 2002 17:15:35 EST
    ...I seem to recall that engine wear is proportional to piston feet per mile. How far a piston travels in moving the car one...
  • Re: [VB] Engine Ceramics Web Page is up and running.
    Historical mailing list - Stan Wilder
    Sat, 5 Apr 2003 23:37:41 -0600
    I sent Thom a picture of a piston. The piston was coated by a West Coast Company. I haven't got pictures of my...
  • Syncro sporadic starting
    Historical mailing list - Skip Emmert-Keaton
    Tue, 27 Jan 2004 10:39:37 -0800
    If the pistons were seizing, how would that effect a push start? I can push start the van by myself (with a few acrobatics...
  • why does #3 pist/cyl always go bad first?
    Historical mailing list
    Mon, 24 Aug 1998 19:25:26 EDT
    why does #3 piston and cylinder always go bad first on the aircooled type 4 engines? had the same prob on 2 engines...always...
  • Re: New Toy
    Historical mailing list - Sam Williams
    Fri, 24 Sep 2004 00:34:36 EDT
    If you leave a vehicle parked for a long time the piston rings can get gummed up. After a little running they will ungum...
  • Head removal: Cylinder sleeves came off (also, how to send gerry messages)
    Historical mailing list - Wesley Pegden
    Sat, 26 Apr 2008 12:48:28 -0400
    ...remove the old piston rings 3. use a broke piece of old piston ring to clean out the ring grooves on the piston (suggested...
  • Re: Off topic - Aircraft Engine
    Historical mailing list - Stan Wilder
    Thu, 19 Jun 2003 23:28:02 -0700
    ...The pistons were double ended, > and > as the crank rotated, the waffle plate wobbled, and being in the > slot on > the pistons, made the...
  • Re: Piston Pin
    Historical mailing list - Don Kane
    5 May 1995 10:05:15 U
    ...RE>Piston Pin Vahid Lajevard writes >I am doing a mini rebuild on my 80 vanagon. By mini rebuild I mean I am >changing...
  • Re: Piston Pin
    Historical mailing list
    Thu, 04 May 1995 13:38:19 +0600
    ...Once the pin has reached the outside of the piston, You have to put a socket on the bolt and start tightning again. The...
  • Re: Front calipers '72 bus
    Historical mailing list
    Thu, 11 Apr 1996 17:25:15 -0300 (ADT)
    ...That was the rebuild extent. (The master cyl kit cost $8 at the time.) If the pistons are badly pitted you need new ones...
  • front brake pads, how?
    Historical mailing list - Gregory M Daughtry
    Sun, 07 Jul 96 20:56:00 PDT
    ...Bentley says that once the old ones are replaced, "push" the piston back into the caliper housing so it will have enough clearance to...
  • Re: 1.9 or 2.1
    Historical mailing list - Benny boy
    Tue, 9 May 2006 22:16:41 -0400
    ...the crank (piston stoke) is the main difference between the 2 engines The short story is: i never seen a rod go through a...
  • Re: cylinder heads for my 84 westy
    Historical mailing list - Frank Condelli
    Wed, 11 Jun 2008 06:07:52 EDT
    ...The right way is to remove the piston pins which entails removing lots of cooling tubes and the waterpump as the pistons are first...
  • Re: Should i sell?
    Historical mailing list - Mark A. Rokus
    Tue, 17 Jun 1997 21:21:48 -0700
    ...did the heads or pistons get changed durring the rebuild? If so it may be that the compression ratio has been changed. In fact...
  • Air Cooled Technical Question
    Historical mailing list - Stan Wilder
    Fri, 1 Jun 2001 08:35:43 -0500
    ...I invite your comments on this matter. *fitting the first and second ring on this #3 piston slightly looser than the specification could be...
  • Re: 85 Head Job Update and Question
    Historical mailing list - Ben huot
    Thu, 6 Jun 2002 14:35:50 -0400
    ...Be careful (if you put new rings) to respect the 120 deg angle for the 3 rings opening per piston. (if I remember right...
  • To split the case or not on a rebuild?
    Historical mailing list - Markus Kruse
    Tue, 9 Jul 2002 10:42:11 -0400
    So, I put two new heads on the 89 (110,000 miles) and put new rings on the pistons... Now it uses 1 quart...
  • f/s '87 syncro (update)
    Historical mailing list - Mail Server
    Tue, 15 Jan 2002 21:39:33 -0800
    ...I had the heads off about 12000 miles ago chasing the noise, thinking it might be a piston, but pistons and rings looked good...
  • Re: Brake Fade
    Historical mailing list - Dennis Haynes
    Mon, 12 Sep 2011 01:24:46 -0400
    ...Brake Fade Pistons and pins moving smoothly. video of wheel cylinder "pullback" syndrome. http://www.youtube.com/watch?v=mQrTuwBdXxs&feature=related Edward At...
  • Re: compressing piston rings in engine
    Historical mailing list - Richard A Jones
    Tue, 10 Dec 2013 08:31:33 -0700
    > adds a few hours to the job and gives a reason to replace the water pump. My experience is that in a waterboxer, the...
  • Re: diagnosis--blown piston ring?
    Historical mailing list - Paul Guzyk
    Fri, 27 Mar 2009 15:55:22 -0400
    Before pulling the engine, remove the valve cover, turn the engine over by hand (or with starter & ignition disconnected) and see if the valve...
  • A stuck Sleeve....
    Historical mailing list - Ken Lewis
    Fri, 14 Oct 2011 16:04:07 -0400
    Greetings and Salutations, Anyone have a trick for getting out a stubborn piston cylinder? Number two and four refuse to budge. I have been...
  • Re: Stuck cylinders
    Historical mailing list - HotelWestfalia
    Fri, 11 Nov 2011 18:20:22 -0800
    ...WD40, banging on a 2x4 on the piston going inwards while the crank was turned with a long breaker bar. You can beat on...
  • Re: Master Cylinder
    Historical mailing list - Jim Felder
    Wed, 1 Mar 2006 06:34:46 -0600
    What Mark said--the piston may be letting fluid leak past it, rather than push fluid out of the system where you can see...
  • Re: why no ridge in waterboxer cylinders?
    Historical mailing list - kenneth d lewis
    Fri, 10 Jul 1998 22:21:39 EDT
    Maybe because of the type of combustion chamber, which resides INSIDE the piston itself. Drive Safely & Good Luck Ken Lewis<Kernersville,NC> On Fri...
  • Re: [*sp@m*] Re: Compression test - cold vs hot?
    Historical mailing list - Jaap Nauta
    Fri, 18 Mar 2005 23:40:37 +0100
    ...Start with a (hand)warm engine, so piston and cylinder are closer to working temperature, measure compression, that some oil in the cylinder, and...
  • Re: Clutch Throw-out bearing
    Historical mailing list - Ben
    Thu, 8 Mar 2007 14:27:22 -0500
    ...attached to > clutch operating arm? > > Pedal down, slave piston pushes arm down, pedal up piston and arm go > up and spring helps keep arm...
  • Re: Auto trans - 2nd gear brake band adjusting screw
    Historical mailing list - BenT Syncro
    Thu, 10 Mar 2011 22:26:28 -0800
    ...failure in the 2nd gear piston mentioned by Ken under the > |>> circlips > |>> on the DS. > |>> If the rubber piston seals are cracked, aged to...
  • Where to buy a balanced engine? was: Engine balancing
    Historical mailing list - Bulley
    Thu, 2 Dec 1999 10:55:17 -0500
    ...Engine balancing > >Can anyone explain to me the process/procedure for balancing the >internal parts of an engine....pistons, rods, etc, and dynamic balancing...
  • Re: Serious question
    Historical mailing list - G. Matthew Bulley
    Fri, 25 Jan 2002 22:24:42 -0500
    ...Serious question Why is it usually that #3 piston that goes? William P. > About five years ago I blew #3 piston trying to abate...
  • Re: Commentary on Air Cooled Cylinder Heads
    Historical mailing list - Robert Donalds
    Tue, 25 Jun 2002 12:19:19 -0400
    ...I hone the cylinders for more piston to skirt clearance as well as notch the con rods to spray oil at the pistons. the...
  • Re: Disc brake calipers
    Historical mailing list - John Pronk
    Fri, 10 Aug 2001 08:04:46 -0000
    ...only one piston, one set > >of seals etc? > > No. The manufacturers, being responsible people, realized that the old > fixed calipers did not work at...
  • Re: How do you split the case?
    Historical mailing list - ROBERT DONALDS
    Mon, 23 Oct 2006 18:09:32 -0400
    you need to remove the pistons in order to separate the case. The case must have some hardware left in place or you would...
  • Re: Synthetic Oil
    Historical mailing list - Michael Snow
    Sun, 31 Mar 2002 15:08:38 -0800
    ...Horizontally opposed engines like the WBX will always consume more oil during engine warmup than an engine with vertical piston travel. What percentage of...
  • SD7H15 AC compressor replacement?
    Historical mailing list - Paul Retherford
    Fri, 27 Jun 2003 11:02:22 -0500
    ...wondered if one of these would work in place of SD709 for vanagon? http://www.sanden.com/products/piston7.html Thanks, Paul '89 Westfalia
  • Re: Lower bleeder screw question (searched archives)
    Historical mailing list - Mike Collum
    Sun, 15 Apr 2007 09:14:44 -0400
    Vanagons have the 2 piston calipers through model year '85. You do want to "Purge" the old fluid from both bleed screws on each...
  • Re: Engine Rebuild Questions
    Historical mailing list - Tom Hargrave
    Tue, 7 Apr 2009 23:17:47 -0500
    ...Why is it important to replace the Pistons if they look fine? I understand the rings and other components but why the actual piston...
  • 2.1 long block
    Historical mailing list - dawn
    Sun, 18 Mar 2001 09:42:51 -0800
    ...the piston did not receive any fuel to cool the piston down it seized causing the crank shaft rod to explode the piston in...
  • Re: oil pressure
    Historical mailing list - Thomas Pfrommer
    Mon, 7 May 2007 10:52:24 -0700
    ...that means the spring connects to the outer ring of the piston and it is hollow at the spring site. The piston is flat...
  • Re: 112HP @ 4800RPM on a stock WBX?
    Historical mailing list - Per Lindgren
    Sun, 26 Mar 2000 05:57:29 +0200
    Gary McEachern wrote: > What's different about the DJ engine from the MV? Is it just pistons and > longer connecting rods or are there...
  • Re: It's not moving...UGH!!!
    Historical mailing list - James Bowen
    Tue, 19 Jun 2001 18:00:26 EDT
    ...After confering with several pros, I came to the conclusion that all of the seals, pistons, and friction clutches in the tranny were going...