

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 15+: 60 results shown for Cylinder head.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Re: Heads are off; now what?Historical mailing list - Stan SmithThu, 22 Feb 2001 07:56:10 -0500Karl, I've had the heads off my 85 Westy a few times, for gasket replacements. I have not taken the pistons and cylinders...
- Re: EGT temperatureHistorical mailing list - Spooner, Robert E.Wed, 2 Jan 2002 11:26:36 -0500...I think EGT is more informative than cylinder head temp. " From my kart racing days, the EGT is about a million times more useful...
- Noisy cylinder headHistorical mailing list - Rick CooperTue, 18 Jun 2024 07:02:40 -0600...For the last couple hundred miles there has been mechanical noise coming from the LH cylinder head. My guess is that the rocker assembly...
- Re: I'll Try Again... Advice on VDO Cylinder Gauge on a 2.1L????Historical mailing list - Stan WilderMon, 30 Jun 2003 12:49:48 -0700...I'll try again. > > Anyone have thoughts on whether a VDO Cylinder Head > Gauge would be useful on a 2.1L? I know they...
- Good set of 2L core heads (square port 79-83.5) heads for saleHistorical mailing list - Vanagon manThu, 5 Dec 2002 09:42:06 -0500...One head has a small crack between the valves on both cylinders, and the other head has a crack at the spark plug hole...
- Re: Coolant pressure test... video.Historical mailing list - Dennis HaynesWed, 16 Dec 2009 00:07:18 -0500Actually you either have a cracked head or more likely the head studs failed to maintain pressure under load (that stretch preload thing) the...
- Re: Is mechanic on the level?Historical mailing list - DAVID MOSTSun, 31 Jan 1999 09:14:57 -0800...If I do have a slight leak in the vanagon slave cylinder, am I headed that way if I don't replace it? On...
- Exhaust cylinder studs & threadlockHistorical mailing list - Georgios A. Stylianides, PhDMon, 27 Aug 2007 19:36:43 -0700Hi all, Back to the exhaust system and crossover front and rear pipe attachment to the cylinder heads. Details below. My original question: what...
- Cause of broken valve?Historical mailing list - jonSat, 2 Aug 2003 10:18:26 -0700...The engine is pretty clean, and when I removed the cylinder head covers, the heads look pretty darn good. So, I hope this engine...
- Cracks in cylinder headsHistorical mailing list - Walter E. StephensWed, 8 Jul 1998 16:57:52 -0700...All four cylinders have this condition. Is this common? What should I do about it? Any thoughts would be appreciated. Walter E. Stephens ACS...
- Re: WBX Cylinder Head Nut Torque check, re-torqueHistorical mailing list - Neil NFri, 15 Jul 2016 13:24:05 -0700...Looking further in Bentley manual, interesting to see that theres pages on "Cylinder head resealing". I don't see any note there about re...
- Re: Piston Ring ReplacementHistorical mailing list - Kenneth WilfordMon, 14 May 2007 11:40:17 +0000You definately want to hone the cylinders if you are putting in new rings. I would remove the piston heads and fully clean them...
- Re: 91 Headlight switch...Historical mailing list - mark drillockSat, 4 Jun 2005 08:47:13 -0700...The ignition lock cylinder is just metal that turns with the key. The cylinder part has a small tab that sticks into a slot...
- Re: Cutting tool question...cylinder head pocketHistorical mailing list - Scott Daniel - TurbovansFri, 10 May 2013 20:02:48 -0700'pocket width' ..... 'pocket' in cylinder heads to me means the area the valves sit in ...like how much relief there is around them. porting...
- '84 Westy on CL in Richmond B.C. - $2150Historical mailing list - neil NFri, 15 Aug 2008 10:35:09 -0700...heads up" for a swap maybe? Cheers, Neil. -- Neil Nicholson '81 JettaWesty "Jaco http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder...
- WBX ReliabiltyHistorical mailing list - John LunettaSun, 17 Feb 2002 08:27:59 -0500...I have my van since new in 1990, I have 170,000 miles and only one cylinder head leak repair. Only let me down...
- Subaru Gurus...Historical mailing list - Jeffrey SchwaiaTue, 21 Jan 2003 12:36:30 -0800Hey Subaru Gurus, Whilst wandering the junkyard this weekend, I noticed almost all the Subarus were missing their cylinder heads. Are the heads a...
- Re: Cylinder Head differencesHistorical mailing list - Kenneth LewisFri, 27 Apr 2007 22:20:16 -0400...All things being equal and substituting the1.9L heads on a 2.1L long block; I arrived at an increase of compression ratio to...
- Re: air cooled 2.0 1981 Cylinder head temp?Historical mailing list - Neil NThu, 6 Feb 2014 13:32:08 -0800...Having mechanic put a Dokata cylinder head sensor > under #3 plug, to gauge on dash. What should the temperture be? -- Neil n Blog: tubaneil...
- Re: Originally: JLP rebuilt wbxr engines in DenverHistorical mailing list - John RodgersWed, 9 Feb 2011 16:11:58 -0600...The cylinder bores and possibly the rings are identical. > > I believe it is about time to reseal my 2.1 cylinder heads. I may...
- Re: update on oil spray problemHistorical mailing list - Brad HoppTue, 27 Sep 1994 15:46:19 -0700 (PDT)...15.9 Cylinder Head gasket identification: Locate the part number on the gasket and use that. Each gasket has a unique part number stamped...
- Re: WBX Cylinder Head Nut Torque check, re-torqueHistorical mailing list - Stuart MacMillanFri, 15 Jul 2016 13:09:52 -0700...WBX Cylinder Head Nut Torque check, re-torque Hi all I'm searching but don't see a clear direction on this. For checking...
- Re: Need three parts for a 2.1 engineHistorical mailing list - Scott Daniel - TurbovansMon, 12 Nov 2012 19:32:12 -0800had me wondering there .. 'aluminum head gasket' .. must be the metal sealing rings that go on top of the cylinder barrles. Got lots of...
- Re: Frozen slave cylinderHistorical mailing list - Roger SislerFri, 17 Mar 2006 12:31:58 -0500...the head of the last mounting bolt ,and remove thenut. While still holding the bolt in place,remove and toss the old cylinder over...
- Re: NEED HEAD adviceHistorical mailing list - Joe L.Mon, 2 Nov 1998 09:55:43 -0500...If you have the Haynes manual it will tell you that it is OK to pull the cylinders out with the heads. THIS IS...
- Re: Machining Cylinder Heads a Viable Solutuion Problem?Historical mailing list - Mark GajewskiWed, 6 Jan 1999 17:14:42 -0500...Machining Cylinder Heads a Viable Solutuion to >> Wasserboxer Problem?Dear Readers: Is it possible to repair >> the Wasserboxer head problem by machining flat the...
- Re: Rebuild timeHistorical mailing list - david kaoSun, 01 Dec 1996 21:38:10 -0800...If it is within 150k miles the most likely rebuild needed is the cylinder heads and possibly cylinders/pistons. You can buy rebuilt or...
- Re: Compression lossesHistorical mailing list - Blue EyesTue, 5 Jan 1999 11:24:16 -0600...The compression ratio is the numerical comparison of the volume contained by the cylinder plus the cylinder head when the piston is all the...
- Engine ground strapsHistorical mailing list - Shawn WrightSun, 6 Jun 1999 17:53:13 -0700Today I started cleaning up and checking ground straps in the engine compartment, and found that the right side cylinder head did not have...
- Re: NAPA Part Number for Hose?Historical mailing list - Gerald MasarMon, 14 Jun 2004 12:55:52 -0700...I was > able to fabricate plugs at the cylinder head and at the "T", refill the cooling > system and drive the van home. > > Is...
- Rotten Head Studs (and names)Historical mailing list - Dyer LytleWed, 8 Jun 2005 11:15:30 -0700...I may have reported before that the failure that led to this rebuild was the breakage of a cylinder head stud and the various...
- Source of interior panel fastenersHistorical mailing list - jonMon, 4 Aug 2003 17:54:44 -0700...So, I have the head bolts off of one head, but cannot seperate the head from the cylinder jugs. I spray penetrating oil, so...
- Re: NEED HEAD adviceHistorical mailing list - William H. CollinsTue, 3 Nov 1998 12:09:20 EDTThere is a way (documented in the archives somewhere) to remove the waterboxer heads (with cylinder sleeves still attached), while leaving the pistons attached...
- Re: Head Gasket sealant sorry 1 more timeHistorical mailing list - TCWed, 21 Nov 2007 07:02:04 -0800> ALL, and I mean ALL the head gaskets I have installed with both Loctite > Ultra Copper RTV Hi-Temp Silicon Sealant do you use...
- misfire - diagnosis of problem?Historical mailing list - Craig OdaMon, 4 Oct 2004 10:02:01 -0700I have a misfire in one of the cylinders that is resulting in incomplete combustion and higher than normal emissions. I have had this...
- T4 cylinder base shimsHistorical mailing listThu, 21 Mar 1996 14:48:31 -0600Volks, I need to find some 060 cylinder base shims for my 1700 ('72 Westy) T4 engine. The VW dealer says he stocks nothing...
- ? more leaky heads...Historical mailing listThu, 14 Dec 1995 09:03:37 -0500 (CDT)...Now, I'm back to JUST redoing the heads myself. I'll send the heads and cylinders off to have them checked and fixed...
- '83 wasserboxer - valve adjustment advice?Historical mailing list - James, DanielFri, 19 Feb 1999 11:33:53 -0800Volks, An unsettling lack o'compression in cylinder #3 has me investigating the procedure for adjusting valves. (BTW - the PO had the heads done...
- Re: Help! Cylinder head stud brokenHistorical mailing list - Paul GuzykWed, 9 Mar 2005 21:21:35 -0800I think it was number 8 (as shown on page 15.23 of Bentley) >>Thanks Paul for replying my post, do you remember which...
- Leaky Head Nut?Historical mailing list - Walter E StephensTue, 14 Aug 2001 16:58:03 -0700I have just replaced the head on 90 Vanagon with a 2.1L engine. I have a leaky cylinder head nut. I have tried...
- Re: head gaskets and time bombsHistorical mailing listMon, 5 Feb 1996 22:18:53 +0000...that, when it blew a head gasket, the increased > >pressure of coolant leaking into one of the cylinders while it was running > >at freeway...
- Re: More questions as the rebuild progressesHistorical mailing list - Steven JohnsonTue, 18 Jun 1996 08:08:43 -0700 (PDT)...mine with no cylinder honing. This was on my '74 camper. I just rebuilt the top end and had the heads rebuilt/replaced. And...
- [Fwd: Is mechanic on the level?]Historical mailing list - Mike CatlinSun, 31 Jan 1999 11:42:00 -0800...If I do have a slight leak in the vanagon > slave cylinder, am I headed that way > if I don't replace it? Yes...
- Resolved: Vanagon GL 90 2.1L engine unexpectedly stalls while drivingHistorical mailing list - Mike BradenMon, 24 May 2004 09:46:13 -0500...While replacing the spark plugs, I checked the compression of each cylinder. While they are all low (110-120 psi), cylinder one was definitely...
- Re: nasty AMC exhaust valve, photos hereHistorical mailing list - neil NSun, 24 May 2009 00:20:48 -0700...Pulled #1,2 head, noticed this fun stuff inside; #2 exhaust valve was broken off and banging around inside the cylinder. �I guess that...
- Re: [DIESEL] Reinhardt Saga (long)Historical mailing list - David SnyderTue, 17 Aug 1999 20:11:51 -0700...Area of head above #2 cylinder looks like the surface >of the moon. The pre-chamber insert is broken into three pieces and turned...
- Re: nuts vs head gasket jobHistorical mailing list - Tom CarchraeWed, 4 Sep 2013 16:01:07 -0700...the > heads if the problem has not been left so long that the head seals (inners) > or the tops of the cylinders have burned...
- need engine for '87 WestyHistorical mailing list - Diana BroomeThu, 9 Dec 1999 15:03:17 ESTAfter replacing a head gasket, then the cracked cylinder head I've learned that the new head doesn't match with the warped engine...
- new diesel - - one cylinder, no compressionHistorical mailing listThu, 25 Feb 1999 09:59:44 -0700After just 10K miles on my new 1.6 litre TD engine, I find that it began running very rough, like on three cylinders...
- Re: GEX update (fwd)Historical mailing listFri, 26 Jul 1996 18:46:26 -0700...There was exhaust etc from where the head was not meeting > the cylinder. Any one familiar with this one? > This problem sounds like failure...
- Re: off with her headsHistorical mailing list - Scott DanielWed, 16 Oct 2013 18:22:03 -0700...I do them with the piston down, away from the cylinder head. it's ok to turn the engine .. one warning..always keep the...
- My recent engine tear-down: All is good againHistorical mailing list - Don HansonSun, 10 Nov 2013 07:38:00 -0800...I found a blown cylinder head gasket, a small breach between cylinders 3 & 4, across the castings between the pistons. When I built this...
- 2.1 lifter replacementHistorical mailing list - John Lunetta 1990 Vanagon GLTue, 2 Oct 2001 19:32:22 EDTDoes anyone know if you can replace the hydrolic lifters on a 1990 2.1 waterboxer without removing the cylinder heads? I will be...
- Re: New head replacement, bad gas mileage...Historical mailing list - Paul GuzykWed, 13 Apr 2005 11:19:16 -0700...I added a little oil for 1 and 4 >cylinder and test again, both compression went up to 150. I know >this is not...
- Re: lifters for new engine? - and increased strokeHistorical mailing list - Damon CampbellSun, 23 Mar 2003 17:32:33 -0800...So to keep > the piston in the confines of the head/cylinder, the > wrist pin is actually > "higher" in the stroker piston. If you...
- Head Update (getting worse)Historical mailing list - Jere HawnSat, 5 Mar 2005 16:30:11 -0800Greeting all, If you have been following the upper cylinder o-ring blew and I decided to replace the heads while I was doing...
- Re: Finding trustworthy mechanics; was RE: heads- bus depot or
van cafe??Historical mailing list - David KaoMon, 26 Jan 2009 14:07:14 -0800...At that point I had no way to find out if it was my cylinder head any more. I did take that one back...
- Head Leak / Valve JobHistorical mailing list - Daniel ArnfeldWed, 23 Apr 1997 16:23:58 -0700...heads have been removed and cleaned. No real evidence of leaking. But now the important stuff: 1. Is it normal for the cylinders to...
- low compressionHistorical mailing listSun, 20 Apr 1997 20:55:47 -0400 (EDT)...burnt valve?, head gasket?, cracked head?? Also can the head be removed without pulling engine? Anthony
- Re: Looking for SD-510 A/C Compressor PartHistorical mailing list - Ed McLeanThu, 21 Mar 2002 18:20:07 -0500...All three compressors can be obtained with a variety of cylinder head assemblies that have O-ring connections or flair connections on either the...